background image

 

 

Radio Frequency Compliance Statement 

 
IDENTEC SOLUTIONS is the responsible party for the compliance of the following devices: 
 

MODEL: 

 

iQ355 P 

Region/Country 

Organization 

Marking 

EUROPE: 

EU 

CE 

USA: 

FCC 

FCC ID OO4-IDS1000 

CANADA: 

IC 

3538A-IDS1000 

 
The user(s) of these products are cautioned to only use accessories and peripherals approved, in advance, by 
IDENTEC SOLUTIONS. The use of accessories and peripherals, other than those approved by IDENTEC 
SOLUTIONS, or unauthorized changes to approved products, may void the compliance of these products and result in 
the loss of the user(s) authority to operate the equipment. 
 

European Declaration of Conformity according to RED Directive 

 
IDENTEC SOLUTIONS AG hereby declares that the device iQ355 P is in conformity with the essential 
requirements of Directive 2014/53/EU. The declaration of conformity can be found at: 

www.identecsolutions.com

 

 
 

USA Certification

 

FCC Part 15 compliance statement  
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This 
device may not cause harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation. 

 

 

Canada Certification  

Licence-Exempt Radio Apparatus (ISED) 
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic 
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 
1. 

This device may not cause interference. 

2. 

This device must accept any interference, including interference that may cause undesired operation of the 

device. 
 
Appareils radio exempts de licence (ISDE) 
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, 
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. 
L’exploitation est autorisée aux deux conditions suivantes : 
1. 

L’appareil ne doit pas produire de brouillage; 

2. 

L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en 

compromettre le fonctionnement. 
 
 
 
 
 
 

Summary of Contents for IDS1000


















Reviews: