IDEC LONWORKS User Manual Download

Page: 18 / 24

ORKS

® Communication Module User’s Manual

4-3

4.2 Available network variables

The L

ORKS

® Communication Module’s standard LON

application contains the network variables described below.

LonMark Node Object

Quantity

Name

Type

Description

nviRequest0

SNVT_obj_request

Request object mode

nvoStatus0

SNVT_obj_status

Output object status

LonMark Controller Object

SNVT

Description

SNVT_switch

Switch light, alarm, window contact, free inputs / outputs
value=0, state=0

inactive

value>0, state=1

active

SNVT_occupancy

Occupancy:0=occupied

1=not occupied

2=bypass

3=standby

SNVT_tod_event

Scheduler program
Just current state: 0=occupied

3=standby

SNVT_temp_p

Room temperature

SNVT_lux

Brightness – lighting level

SNVT_lev_percent

Position

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for LONWORKS

























Search results

Summary of Contents for LONWORKS

Reviews:

Related manuals for LONWORKS

Brands by name

Popular brands

IDEC LONWORKS, User Manual

Search results

Summary of Contents for LONWORKS

Reviews:

Related manuals for LONWORKS

Brands by name

Popular brands