background image

Rev. 10/05/2012 

automatically dial all the numbers stored, one by one, for

 

the CYCLE (amount of 

times the numbers are dialed) you have chosen. The receiver of the phone call 
will hear 

one beep cycle for zones 1-7 and 8S

two beep cycles for 24hr zone 

and four beep cycles for PANIC

. The receiver of the call can then call a 

neighbor, or take other appropriate action. 

b.

 

In ARM mode, if the auto-dialer is set to 

SIREN OFF

, the numbers stored will be 

dialed silently. No siren will be heard from the installed location.

 

When the call is 

answered you will hear the sequence of beeps and know which zone was triggered.   

 

3. TO DISARM THE SYSTEM 

a.

 

Enter password followed by the ARM/DISARM

  button on the auto dialer. Or 

press on 

DISARM

  button on the remote. (if learned) 

b.

 

You will hear one beep and the ARM icon will disappear from the auto-dialer 
screen to confirm that the Auto-Dialer has been DISARMED. 

NOTE:

 In the 24HR zone, the sensors will trigger the auto-dialer in ARM or 

DISARM mode and start dialing the stored numbers the amount of times programmed 
immediately and the siren will sound. If siren is set to OFF the unit will beep 4 times. 
Before dialing, the auto dialer will detect if a phone line is connected, if no telephone 
line is connected the auto dialer will beep 4 times then the alarm will sound without 
dialing.

 

 
 

4. HOME MODE FUNCTION: 

 
While at home you can set your auto-dialer to home mode. This will activate a chime 
every time a sensor is triggered. If you have installed additional sensors you can also 
program which zone will send signal to auto-dialer when triggered. The factory default is 
all sensors send signal. 

Turn system to Home Mode. 

a.

 

Press the 

HOME

 button once; (on left side of auto-dialer) you will hear a chime 

and the word 

HOME

 will appear on the LCD screen. 

b.

 

Wait 60 seconds, you will hear a beep. System is now in home mode and will 
chime if sensor is triggered. 

c.

 

When auto-dialer receives signal from zones 1-7 & 8S it will chime and show 
which zone is being triggered on the auto-dialer LCD screen. After 5 minutes it 
will reset itself and 

TRIGGER

 will disappear from the screen. If 24hr or panic 

zones are triggered the auto dialer will start dialing the numbers programmed for 
the amount of times specified if telephone line is detected. The auto dialer will not 
reset itself it will keep showing the trigger until you press the 

HOME

 button. 

d.

 

Press the 

HOME

 button again to exit the 

HOME

 mode. 

 

NOTE: Arming system while in HOME mode will deactivate HOME mode. After 
disarming system you will have to press the HOME button again if you want to 
return to HOME mode

In HOME mode the only thing the system does not do is 

dial out or sound alarm for zones 1-7 and 8S. For zones 24hr and REMOTE when 
triggered they will dial out. 

Summary of Contents for SK618

















Reviews: