manualshive.com logo in svg

IDEAL SIGNALTEK, Operation Manuals, Page: 4 / 81

Share
Download
IDEAL SIGNALTEK Operation Manuals Download Page 4

IDEAL INDUSTRIES, Inc.

ii

IDEAL INDUSTRIES STANDARD WARRANTY POLICY

IDEAL INDUSTRIES warrants that all SIGNALTEK Products 
manufactured or procured by IDEAL INDUSTRIES conform to 
IDEAL INDUSTRIES’ published specifications and are free from 
defects in materials and workmanship for a period of two (2) years 
from the date of delivery to the original Buyer, when used under 
normal operating conditions and within the service conditions for 
which they are designed. This warranty is not transferable and 
does not apply to used or demonstration products.

The obligation of IDEAL INDUSTRIES arising from a Warranty 
claim shall be limited to repairing, or at its option, replacing without 
charge, any assembly or component (except batteries and cable 
adapters), which in IDEAL INDUSTRIES’ sole opinion proves to be 
defective within the scope of the Warranty. In the event IDEAL
INDUSTRIES is not able to modify, repair or replace 
nonconforming defective parts or components to a condition as 
warranted within a reasonable time after receipt thereof, Buyers 
shall receive credit in the amount of the original invoiced price of 
the product.

IDEAL INDUSTRIES must be notified in writing of the defect or 
nonconformity within the Warranty period and the affected Product 
returned to IDEAL INDUSTRIES’ factory, designated Service 
Provider, or Authorized Service Center within thirty (30) days after
discovery of such defect or nonconformity. Buyer shall prepay 
shipping charges and insurance for Products returned to IDEAL 
INDUSTRIES or its designated Service Provider for warranty 
service. IDEAL INDUSTRIES or its designated Service Provider 
shall pay costs for return of Products to Buyer.

IDEAL INDUSTRIES shall have no responsibility for any defect or 
damage caused by improper storage, improper installation, 
unauthorized modification, misuse, neglect, inadequate 
maintenance, accident or for any Product which has been repaired 
or altered by anyone other than IDEAL INDUSTRIES or its 

www.vemco.pl

Summary of Contents for SIGNALTEK


















































































Reviews:

No comments