background image

RAJ-7K-H & RAJ-7K-L 

Jun 2022

 

Ensure jack can roll freely on jack rails and all side ‘guide’ rollers are adjusted to 
be in contact with jack rails.

 

SAFETY INSTRUCTIONS 

 

·

 

Never allow unauthorized or untrained persons to operate the rolling jack. 

·

 

Thoroughly train all employees in the use and care of rolling jack. 

·

 

Never overload rolling jack. Capacity of rolling jack is stated on the nameplate. Capacity 
should not be exceeded. 

·

 

Observe and avoid any pinch point areas of the linkage mechanism. 

 

OPERATING INSTRUCTIONS 

 

 

 

To avoid personal injury and/or property damage, permit only trained personnel   

 

 

to operate jack. 

After reviewing these instructions, get familiar with jack controls by running the jack through a few 
cycles before loading vehicle on jack. Observe and avoid any pinch point areas of the linkage 
mechanism. 

1.  Before loading a vehicle onto lift, endure jack(s) are fully lowered. Make sure the rubber blocks 

are in their most inbound position. Also ensure the jack(s) is (are) pushed toward the center of lift 
before driving vehicle on or off lift. This will provide maximum vehicle clearance when loading and 
unloading vehicles. 

2.  After vehicle has been loaded, chock tires on the opposite side in which the rolling jack is to be 

used. If two rolling jacks are to be used, chock the tires on the opposite side of the rolling jack to 
be raised first. 

 

 

 

 

 

Engage runway locks before raising vehicle on jacks! DO NOT operate lift while   

 

 

jacks are engaged with a vehicle! 

3.  Place jack under vehicle at manufacturer

’s recommended pick-up points. Pull out the arms to the 

proper pick-up points. Take up clearance with rubber blocks. 

 

 

Allow 12” minimum clearance between vehicle and nearest overhead obstruction   
before raising vehicle above runways. Failure to comply could damage vehicle 
and/or cause personal injury.

 

4. 

To Raise Rolling Jack: 

Press down on the pump

’s ‘Pressure’ lever until the jack is raised to the 

desired lock position, followed by pressing the 

‘Release’ lever on pump to lower jack onto locks. 

5. 

To Lower Rolling Jack: 

Slightly raise jack to release off locks, followed by moving the lock 

release lever to an upward left position, while carefully pressing down on the pump

’s ‘Release’ 

lever until the jack lowers completely. 

 

 

Always fully lower jack to prevent damage to the vehicle or lift. 

Summary of Contents for RAJ-7K Series











Reviews: