4.1.
Loosen locating bolt at the side of the handle base. Push handle into socket and re-tighten locating bolt, ensuring that it fits correctly in the
groove.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . 2200HL.V2
Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2tonne
Min. Saddle Height: . . . . . . . . . . . . . . . . . . . . . . . 80mm
Max. Saddle Height: . . . . . . . . . . . . . . . . . . . . . 805mm
Max. Chassis Height: . . . . . . . . . . . . . . . . . . . . 220mm
Length:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 950mm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51kg
Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts.
Use genuine parts only. The use of unauthorised parts may be dangerous and will invalidate the warranty.
Locate the jack in a suitable, well lit, work area.
Keep work area clean and tidy and free from unrelated materials.
Use jack on a level and solid ground, preferably concrete.
Avoid tarmacadam as jack may sink in
.
Place suitable wheel chocks under wheels of the vehicle.
Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “Park” if automatic).
Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.
Ensure there are no passengers in the vehicle.
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
Only place jack saddle under those lifting points recommended by the vehicle manufacturer
(see vehicle handbook).
Check the lifting point is stable and centred on the jack saddle.
Ensure the jack wheels are free to move and that there are no obstructions.
Use suitable capacity axle stands under the vehicle before proceeding with any task.
Ensure there are no persons or obstructions beneath the vehicle before lowering.
Use a qualified person to maintain or repair the jack hydraulic system.
When not in use store jack, fully lowered, in a safe, dry, childproof area.
DANGER:
Use the jack for lifting only.
DO NOT
use
for supporting the lifted load.
DO NOT
operate the jack if damaged.
DO NOT
allow untrained persons to operate the jack.
DO NOT
exceed the rated capacity of the jack.
DO NOT
allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.
DO NOT
jack the vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
DO NOT
work under the vehicle until axle stands have been correctly positioned.
DO NOT
use the jack for purposes other than that for which it is intended.
DO NOT
top up the hydraulic system with brake fluid. Use hydraulic jack oil only.
DO NOT
adjust the safety overload valve.
5.1. Priming the hydraulics
5.1.1. Before using the jack for the first time, purge hydraulic circuit in order to eliminate any air in the system. To do so, pull the handle
upward and turn it anti-clockwise to open the release valve. Hold the handle in the open position and pump it up and down 7 or 8
times. To close the hydraulic valve turn the handle clockwise and push down.
5.1.2. Place a few drops of hydraulic jack oil on the pump piston and pump the handle several times to distribute the oil.
5.1.3. Thoroughly lubricate all moving parts.
5.2. General jacking
WARNING! Before lifting ensure Section 1 safety instructions are strictly followed.
5.2.1. Prepare vehicle as described in safety instructions ensuring that the ground on which jack is to stand is level and solid (not tarmacadam).
5.2.2. Position the jack saddle under the vehicle manufacturer’s recommended lifting point (see vehicle handbook).
5.3. Jacking the vehicle
5.3.1. Ensure the release valve is closed (i.e. the handle is pushed down and turned fully clockwise). Commence pumping the handle, or the
foot pedal, using the full stroke, until the vehicle reaches the working height.
5.3.2. Should the jack become overloaded, a safety excess pressure valve will open and stop the vehicle from lifting.
High lift jack arm with incredible low access height of just 80mm. Fitted with quick lift foot pedal and dead man's control. Heavy-duty long
steel chassis with wide wheelbase provides inherent stability and easy access to deep set jacking points. Fitted with one-piece hydraulic unit
with built-in safety overload protection.
InSTrUCTIOnS FOr:
TROLLEY JACK 2TONNE HIGH LIFT LOW
ENTRY
MOdEL nO:
2200HL.V2
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
1. SAFETY
3. SPECIFICATION
2. INTRODUCTION
4. ASSEMbLY
5. OPERATION
2200HL.V2 Issue: 1 - 11/07/14
Original Language Version
© Jack Sealey Limited
