background image

36

 

SERVICING

Ideal Logic Combi - 

Installation and Servicing

36  sERVICINg sChEDULE

F

or the very latest copy of literature for specification & maintenance practices, visit our website www.idealboilers.com, where you 

will be able to download the relevant information.  N.B. Technical Bulletins are also available on www.idealboilers.com.

Warning.

  always turn OFF the gas supply at the gas service cock, and switch OFF and disconnect the electricity 

supply to the appliance before servicing.
Combustion testing must be carried out by a competent person using a combustion analyser conforming to Bs7927.

To ensure the continued safe and efficient operation of the appliance it is recommended that it is checked at regular intervals and 

serviced as necessary.  The frequency of servicing will depend upon the installation condition and usage but should be carried out 

at least annually.  
It is the law that any service work must be carried out by a Gas Safe Registered Engineer. In IE service work must be carried out 

by a Registered Gas Installer (RGII).

INspECTION

1.

  Light the boiler and carry out a pre-service check, noting any 

operational faults.

2.

 Check the flue terminal (and terminal guard if fitted) is 

undamaged and clear of any obstruction.

3.

 Check all water and gas joints for signs of leakage.  Remake 

any suspect joints ensuring a gas tightness check is carried 

out if applicable and the water system is correctly refilled, 

vented and re-pressurised.

CLEaNINg pROCEDURE

Note. 

In order to carry out either servicing or replacement of 

components the boiler front panel must be removed. 

Refer to Frame 37.

1.

  Clean the main burner. Refer to Frame 39.

2.

  Clean the heat exchanger & condensate trap/siphon. Refer to 

Frames 40 & 41.

3.

  Check the main injector for blockage or damage. Refer to  

Frame 45.

4. 

Check that the flue terminal is unobstructed and that the flue 

system is sealed correctly.

ALSO IF THE DHW FLOW RATE IS IN QUESTION :-

5.

  Check the DHW filter for blockage. Refer to Frame 66.

The cleaning procedures are covered more fully in Frames 38-42 

and MUST be carried out in sequence.

IMpORTaNT.
6.

  After completing the servicing or exchange of components 

always test for gas tightness.

7.

  When work is complete the front panel MUST be correctly 

refitted, ensuring that a good seal is made.

do noT oPEraTE the boiler if the front panel is 

not fitted.

8.

  If, for any reason, the condensate trap/siphon has been 

removed ensure the trap is refilled with water before  

reassembling.

9.

  Check the gas consumption.

10. 

Check combustion by connecting the flue gas analyser to the 

flue gas sampling point as shown in the diagram and measure 

CO & CO

2

.

  If the CO/CO

ratio is greater than 0.004 AND the integrity of 

the complete flue system and combustion circuit seals have 

been verified and the inlet gas pressure (and gas rate) have 

been verified, then contact Ideal.

11.

 Complete the service section in the Benchmark 

Commissioning Checklist.

Flue Sampling Point

Air Sample

Point

Ensure all caps and seals

are re-fitted after use

gENERaL

Please note

: During routine servicing, and after any 

maintenance or change of part of the combustion 

circuit, the following must be checked:
-  The integrity of the flue system and the flue seals,
-  The integrity of the boiler combustion circuit and 

the relevant seals

-  The operational (working) gas inlet pressure at 

maximum rate.

-  The gas rate
-  The combustion performance.

COMpETENCE TO CaRRy OUT ThE ChECK 

OF COMBUsTION pERFORMaNCE

Please note

BS 6798:2009 Specification for 

installation and maintenance of gas-fired boilers of 

rated input not exceeding 70kW net advises that:
-  The person carrying out a combustion 

measurement should have been assessed as 

competent in the use of a flue gas analyser and the 

interpretation of the results.

-  The flue gas analyser used should be one meeting 

the requirements of BS7927 or BS-EN50379-3 

and be calibrated in accordance with the analyser 

manufacturers requirements, and

-  Competence can be demonstrated by satisfactory 

completion of the CPA1 ACS assessment, which 

covers the use of electronic portable combustion 

gas analysers in accordance with BS7967, Parts 1 

to 4.

sER

VICIN

g

Summary of Contents for LOGIC Combi E 35













































































Reviews: