background image

 

 

 

 
 
Installation & Operations Manual SunDial

™ Series PV Inverter 

Product Models: 30PV; 30PVF; 30PV+S; 30PVF+S 

MAN-00117, Rev C 

 

Page 

7

 of 

31 

 

 

opening AC and DC Disconnects to assure that the Inverter

’s internal capacitors have 

discharged to zero voltage before performing any work on the Inverter. Utilize lockout 
procedures to insure that both AC and DC Disconnects remain in the off position during 
all service periods. 

 

Warning 

 This photovoltaic rapid shutdown equipment (RSE) does not perform all of 

the functions of a rapid shutdown system (RSS). This RSE must be installed with other 
equipment to form a complete RSS that meets the requirements of NEC (NFPA 70) 
section 690.12 for controlled conductors outside the array. Other equipment installed in 
or on this PV system may adversely affect the operation of the PVRSS. It is the 
responsibility of the installer to ensure that the completed PV system meets the rapid 
shut down functional requirements. This equipment must be installed according to the 
manufacturer’s installation instructions. 

 

Safety Instructions: Battery Installations  

 

Danger 

– 

The Inverter enclosure contains exposed high voltage conductors. The 

enclosure

’s front access and Combiner doors must remain closed, except during 

installation, commissioning, or maintenance by trained service personnel. Do not open 
or remove either door if extreme moisture is present (rain, snow, or heavy dew).  

 

Danger 

– 

To avoid an electric shock, verify that the Inverter

’s external AC and DC 

Disconnects are open (off). A minimum wait time of five (5) minutes is required after 
opening AC and DC Disconnects to assure that the Inverter

’s internal capacitors have 

discharged to zero voltage before performing any work on the Inverter. Utilize lockout 
procedures to insure that both AC and DC Disconnects remain in the off position during 
all service periods. 

 

Warning 

– 

These instructions DO NOT contain any information on the operation of 

battery systems outside of this product. Refer the manufacturer for the battery system 
for installation and servicing instructions.  

 

 

 

Summary of Contents for SunDial 30PV

































Reviews: