background image

3

Standard Height Frame & Header Kits

1 INTRODUCTION

This technical data contains information for dimensioning & assembly 

of a cascade system kit for the Evomax and Evomax 2 ranges.

Header and Frame kits are available in both ‘in line’ (6 boilers long) 

and back to back options (3 boilers long). 

GENERAL DESCRIPTION OF FRAME & HEADER KITS

A requirement to spread the total required heat output over several 

boilers can be accommodated by the use of the Evomax multiple 

boiler frame & header kit options. 

The Varican optional accessory can be installed (1 per boiler) for 

cascade control, see Varican Installation Instructions for further 

information.

The flue configurations for the range of appliances using these 

system kits are C13, C33 & B23 (See appliance manual).

 

Note

. In 

the case of the 150kW boiler, this must be flued in accordance to the 

Clean Air Act. 

All headers and pipe work should be insulated in accordance 

with  the Non Domestic Building Services Compliance Guide. To 

ensure compliance with the maximum heat loss criteria, insulation 

thickness should be calculated according to BS EN ISO 12241 using 

standardised assumptions.

2.1  FRAME AND HEADER KIT DESIGN OPTIONS

The Evomax boilers are suitable for use in a multiple boiler configuration. The Evomax multiple boiler system is available in 

both side by side and back to back options giving the opportunity to choose the optimum footprint size or wall space for a given 

output. Frame 7 states available and gives the minimum number of appliances required, the appropriate floor space & the kit 

product number (N.B. The kits do not include the boilers).

Standard height kits do not include the support frame as the boilers can be wall mounted but a frame kit is available if wall 

space etc. does not facilitate boiler/header wall mounting.

2  GENERAL DESCRIPTION OF CASCADE SYSTEMS

continued . . . . .

Available Evomax 2 Appliances

kW (NG)

Product No.

Ideal Evomax 2 30

220814

Ideal Evomax 2 40

220815

Ideal Evomax 2 60

220816

Ideal Evomax 2 80

220817

Ideal Evomax 2 100

220818

Ideal Evomax 2 120

220919

Ideal Evomax 2 150

220820

kW (Propane)

Product No.

Ideal Evomax 2 30 Propane

220823

Ideal Evomax 2 40 Propane

220824

Ideal Evomax 2 60 Propane

220825

Ideal Evomax 2 80 Propane

220826

Ideal Evomax 2 100 Propane

220827

Ideal Evomax 2 120 Propane

220828

Note.

All boilers need to be sized in accordance to the total required heat load and the modulation capabilities of the appliances.

Low Loss Header Accessories 

(Mixing Header)

DN80

DN100

DN150

219552

219553

219554

Summary of Contents for Evomax 40





























Reviews: