background image

bk

TROUBLES AND CAUSES

(CONCERNING REMOTE CONTROL)

Before you ask for servicing or repairs, check the following points.

If any of the following conditions occur, stop the air conditioner immediately, cut all power to the system, 
and contact a service technician:

•  The indicator lamps flash rapidly (five times per second), you disconnect the unit with the power  and then 
  connect the unit with the power again after two or three minutes but the lamps still flash.
•  Switch operations are erratic.
•  The fuse is blown frequently or the circuit breaker is tripped frequently.
•  Foreign matter or water has fallen inside the air conditioner.
•  Any other unusual condition is observed.

CAUTION

The Transmission Indicator  "   "  Never Comes On

The Display Never Comes On

Symptoms

Symptoms

Causes

Causes

Reason and Disposal

Reason  

The remote control signal is 

not transmitted even when 

the ON/OFF button is pushed.

The TEMP. indicator does 

not come on. 

Check whether the batteries

in the remote control are

exhausted.

Check whether the MODE 

indicated on the display is

"FAN ONLY".

The remote control signal is 

not transmitted, because the

power supply is off.

The temperature cannot be 

set during fan only operation. 

The Display Goes Off

Symptoms

Causes

Reason

The indication on the display

disappears after a lapse of

time.

The ON TIMER indicators 

go off after a lapse of certain

time.

Check whether the timer

operation has come to an

end when the OFF TIMER

is indicated on the display.

Check whether the timer

operation is started when

the ON TIMER is indicated

on the display.

The air conditioner operation

stops since the set time 

elapsed.

When the time set to start the 

air conditioner is reached, the

air conditioner will automatically

start and the appropriate

indicator will go off.

The Signal Receiving Tone does Not Sound

Symptoms

Causes

Disposal

No receiving tone sounds

from the indoor unit even

when the ON/OFF button is

pushed.

Check whether the signal

transmitter of the remote

control is properly directed

to the receiver of the indoor

unit when the ON/OFF button

is pushed.

Direct the signal transmitter of

the remote control to the 

receiver of the indoor unit, and

then repeatly push the ON/

OFF button twice.

Buttons on the remote

controller don't work.

Press Reset button.

Setting Change is Impossible

Symptoms

Causes

Reason and Disposal

The fan speed can not be 

changed.

Check whether the MODE

indicated on the display is

"AUTO"

Check whether the MODE

indicated on the display is

"DRY"

When the automatic mode is

selected, the air conditioner

automatically selects the fan

speed.
When dry operation is selected,

the air conditioner automatically

select the fan speed. The fan 

speed can be selected during

"COOL" and "FAN ONLY", and "HEAT"

Summary of Contents for 700026













Reviews: