background image

Patent No. US 8,856,780 CA 2759622

INSTALLATION CHECKLIST

 - 2 OF 2

CHECKLIST - WITH OEM KEYFOB

1

WARNING: Vehicle engine will start many times. Test in a well ventilated area.

2

Close all vehicle doors, hood and trunk.

3

Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.

¨

Question 1:

 Does the vehicle remote start?

YES: Go to next step.

¨

NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.

4

Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.

¨

Question 2:

 Does the vehicle shut down?

YES: Go to next step.

¨

NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.

5

RAP Shutdown test

¨

Question 3: 

 Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?

YES: Go to next step.

¨

NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.

6

Open hood.

7

If not already installed, affi x the mandatory orange warning sticker under the hood and proceed to next step.

8

Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.

¨

Question 4:

 Does the vehicle remote start?

YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.

¨

NO: Go to next step.

9

Close hood. 

10

Enter vehicle and close the doors.

11

Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.

12

Wait for the vehicle to start.

13

Press brake pedal. 

¨
¨

Question 5:

 Does the vehicle shut down?

YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if 

applicable, and call technical support.

14

Exit vehicle.

15

Installation checklist completed.

www.idatalink.com

Automotive Data Solutions Inc. © 2021

HCX

PAGE 15 OF 15

• 20211105

Summary of Contents for HCX
















Reviews: