manualshive.com logo in svg

ICS SpeedHook 814PRO, Operator'S Manual, Page: 14 / 18

Share
Download
ICS SpeedHook 814PRO Operator'S Manual Download Page 14

© 2022 ICS, Oregon Tool Inc.  Specifications are subject to change without notice.  REV071918~  F/N 74595

814PRO OPERATOR’S MANUAL

14

TROUBLESHOOTING

TROUBLESHOOTING

•

SLOW DIAMOND CHAIN SPEED

 – Be sure the powerpack is providing the correct hydraulic

pressure and flow (8 gpm / 30 lpm at 2,500 psi / 172.5 bar).

•

POOR CUTTING SPEED

 – The diamonds may be glazed over. Make a few cuts in an abrasive

material such as a cinder block to expose the diamonds.

•

PREMATURE CHAIN STRETCH

 – Not enough water pressure. The minimum water pressure is

20 psi (1.5 bar). Insufficient water supply will result in excessive wear on the chain, which can lead
to loss of strength and chain breakage.

•

CHAIN TENSIONER BREAKAGE

 – Side cover nuts are not tight enough.

Torque to 20 ft-lbs (27 Nm).

•

WATER NOT FLOWING

 – Water hose is kinked or supply is not turned on.

•

MOTOR WON'T TURN

 – Hydraulics are hooked up backwards or powerpack is set on reverse

flow.

Further questions? 

Call 800.321.1240

or

visit our website at:

icsdiamondtools.com

Summary of Contents for SpeedHook 814PRO



















Reviews:

No comments