background image

Industrial Contractors’ Supplies, Inc.

- Dust Control Division -

15061 Route 30, N. Huntingdon, PA  15642
Phone: 412 . 824 . 6933

Fax: 412 . 824 . 4704

         www.ICScompany.net

INDUSTRIAL POWER BLOWER

OPERATIONS MANUAL 

Introduction

 

INDUSTRIAL CONTRACTORS SUPPLIES is a leading distributor of products and 

accessories for environmental management in construction, industry and facility
maintenance applications.

With the invention of the Dust Director

®

, a dust control guard for handheld angle grinders

that prevents silica dust from becoming airborne while providing the operator with complete
visibility of the blade and cutting surface, ICS has since established ourselves as a leader and
innovator in the air movement and dust control industry.

About This Manual

This manual is produced solely for the use of  purchasers and operators of our Industrial
Power Blowers and Accessories.  The intent of this manual is to provide the owner/operator of
our products general and specific information regarding the safe and proper operation and
maintenance of the equipment described within. 

Contact

  

If after careful review, any questions arise concerning any portion of this manual,

contact INDUSTRIAL CONTRACTORS SUPPLIES for assistance at:

INDUSTRIAL CONTRACTORS SUPPLIES, INC.  

Phone:  (412) 824-6933 

15061 Route 30, N. Huntingdon, PA 15642 

FAX:  (412) 824-4704 

E-MAIL:  

[email protected]

 

WEB SITE:  

www.ICScompany.net 

-1-

Summary of Contents for EBS-16












Reviews: