manualshive.com logo in svg

ICRealtime Edge IPEG-D20F-IRW3, User Manual

The ICRealtime Edge IPEG-D20F-IRW3 is a cutting-edge surveillance camera equipped with advanced infrared technology. Capture high-quality footage day or night with this durable and efficient device. Enhance your security setup by utilizing its intelligent features. For complete control and understanding of this product's capabilities, you can easily download the user manual for free from manualshive.com.

Share
Download
background image

For Active Deterrence cameras with red and blue alarm light, only

Flicker

is supported in

Mode

.

●

Duration

: After setting warning light duration, the warning light is turned off after an extended

time of period after an alarm. It is 5 seconds–30 seconds.

●

Period

: The schedule when the light will be active. When an event is triggered during the

configured period, the system turns on the warning light. For the configuration, see "5.1.1.1
Setting Period".

Figure 5-13 Warning light linkage

5.1.1.8

Audio Linkage

When enabled, the IPC will broadcasts alarm audio file when an alarm event occurs. Select

Setting

>

Camera

>

Audio

>

Alarm Audio

to set alarm audio file.

Figure 5-14 Audio linkage

5.1.2 Subscribing Alarm

5.1.2.1

About Alarm Types

For alarm types and preparations of alarm events, see Table 5-2.

Table 5-2 Description of alarm types

Alarm Type

Description

Prerequisites

Motion Detection

An event is triggered
when moving object is
detected.

Motion detection is enabled.
For details, see "5.4.1 Setting
Motion Detection".

Disk Full

An event is triggered when
the free space of SD card is
less than the configured
value.

The SD card is installed and
the no space function is
enabled. For details, see
"5.19.1 Setting SD Card".

Disk Error

An event is triggered when
there is failure or
malfunction in the SD card.

SD card failure detection is
enabled. For details, see
"5.19.1 Setting SD Card".

Video Tampering

An event is triggered when
the camera lens is covered
or the video images becomes
unfocused.

Video tampering is enabled.
For details, see "5.4.2
Setting Video Tampering".

127

Summary of Contents for Edge IPEG-D20F-IRW3









































































































































































































Reviews:

No comments

Related manuals for Edge IPEG-D20F-IRW3

Lamperd MSS100 User Manual preview
MSS100
Brand: Lamperd Pages: 16
YesCam Yes727 User Manual preview
Yes727
Brand: YesCam Pages: 58
IDEM SAFETY SWITCHES KL1-P Operating Instructions preview
KL1-P
Brand: IDEM SAFETY SWITCHES Pages: 2
Dakota Alert DCPAS-4000 User Manual preview
DCPAS-4000
Brand: Dakota Alert Pages: 18
TRENDnet TV-IP672PI Quick Installation Manual preview
TV-IP672PI
Brand: TRENDnet Pages: 9
Interlogix DC418 Operation And Installation Manual preview
DC418
Brand: Interlogix Pages: 6
Lorex CVC6975HR Quick Setup Manual preview
CVC6975HR
Brand: Lorex Pages: 2
Clas Ohlson RC4020 Manual preview
RC4020
Brand: Clas Ohlson Pages: 44
HIKVISION IPC-B220-IZ Quick Start Manual preview
IPC-B220-IZ
Brand: HIKVISION Pages: 39
E-matic PMSC Instruction Manual preview
PMSC
Brand: E-matic Pages: 5
United Technologies Interlogix RF440I4 Installation Sheet preview
Interlogix RF440I4
Brand: United Technologies Pages: 4
Olympus 17mm 1:2.8 Instructions Manual preview
17mm 1:2.8
Brand: Olympus Pages: 66
Huviron SK-2020 Instruction Manual preview
SK-2020
Brand: Huviron Pages: 2
Secure Caregiver CAS-FAM Instructions preview
Caregiver CAS-FAM
Brand: Secure Pages: 3
Leica SF 26 Instructions Manual preview
SF 26
Brand: Leica Pages: 358
Lilin CMR6082MX3.6 N Instruction Manual preview
CMR6082MX3.6 N
Brand: Lilin Pages: 12
A1 Security Cameras BN481E82 Quick Installation Manual preview
BN481E82
Brand: A1 Security Cameras Pages: 2
Q-See QC40108-818 Quick Installation Manual preview
QC40108-818
Brand: Q-See Pages: 9

Brands by name

Popular brands

Load more brands