ICPDAS LRA-900-E User Manual Download Page 8

Page: 8 / 55

LRA-900-E (Ethernet to LoRa Radio Modem) User Manual

Version 1.0.1

Page

：

2. Hardware Information

This chapter provides a detailed description of the front panel, the hardware specifications and

the dimensions for the LRA-900-E module.

2.1. Specifications

RF Interface

Radio Frequency

864~ 871.5MHz, 915~ 922.5MHz
(channel: 32, recommend using 868 +/- 4 MHz)

Baud Rate

10000 ~ 250 bps

Transmission Power

15 dBm (Max.)

Antenna

2 dBi Omnidirectional Antenna

Transmission Distance

up to 1500 m ( with 10,000 baud, in free field conditions )

Group ID

0~255

Protocols

Transparent transmit

Configuration

Web Server

Ethernet Interface

Ethernet

10/100 Base-TX, 8-pin RJ-45 x 1, (Auto-negotiating, Auto-MDI/MDIX,

LED indicator)

LED Indicators

Red/ Green/ Yellow

Power / RF TxD / RF RxD Status

EMS Protection

ESD

+/- 4 kV Contact

EFT

+/- 1 kV

Surge

+/- 1 kV

Power

Power Input

+10 V

~ +30 V

Power Consumption

1.5 W (Max.)

Mechanical

Dimensions (W x L x H)

110 mm x 83 mm x 33 mm ( not include antenna )

Installation

DIN-Rail

Environment

Operating Temperature

-25 °C ~ +75 °C

Storage Temperature

-30 °C ~ +80 °C

Relative Humidity

10 ~ 90% RH, Non-condensing

Note: RF Port = TCP Port 10001

Summary of Contents for LRA-900-E























































Search results

Summary of Contents for LRA-900-E

Reviews:

Brands by name

Popular brands

ICPDAS LRA-900-E, User Manual

Search results

Summary of Contents for LRA-900-E

Reviews:

Brands by name

Popular brands