background image

3

1.  It is the responsibility of the owner to ensure 

that all users of this treadmill are adequately 

informed of all warnings and precautions.

2.  Before beginning any exercise program, 

consult your physician. This is especially 

important for persons over age 35 or persons 

with pre-existing health problems.

3.  The treadmill is not intended for use by 

persons with reduced physical, sensory, or 

mental capabilities or lack of experience and 

knowledge, unless they have been given 

supervision or instruction concerning use 

of the treadmill by someone responsible for 

their safety.

4.  Use the treadmill only as described in this 

manual.

5.  The treadmill is intended for home use only. 

Do not use the treadmill in any commercial, 

rental, or institutional setting.

6.  Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a 

garage or covered patio, or near water.

7.  Place the treadmill on a level surface, with 

at least 8 ft. (2.4 m) of clearance behind it 

and 2 ft. (0.6 m) on each side. Do not place 

the treadmill on any surface that blocks air 

openings. To protect the floor or carpet from 

damage, place a mat under the treadmill.

8.  Do not operate the treadmill where aerosol 

products are used or where oxygen is being 

administered.

9.  Keep children under age 16 and pets away 

from the treadmill at all times.

10. The treadmill should be used only by per-

sons weighing 300 lbs. (136 kg) or less.

11. Never allow more than one person on the 

treadmill at a time.

12. Wear appropriate exercise clothes while 

using the treadmill. Do not wear loose 

clothes that could become caught in the 

treadmill. Athletic support clothes are recom-

mended for both men and women. Always 

wear athletic shoes. Never use the treadmill 

with bare feet, wearing only stockings, or in 

sandals.

13. Plug the power cord into a surge sup-

pressor (not included), and plug the surge 

suppressor into an appropriate outlet (see 

page 17). To avoid overloading the circuit, 

do not plug other electrical devices, except 

for low-power devices such as cell phone 

chargers, into the surge suppressor or into 

an outlet on the same circuit.

14. Use only a surge suppressor that meets all 

of the specifications described on page 17. 

To purchase a surge suppressor, see your 

local PROFORM dealer, call the telephone 

number on the front cover of this manual, or 

see your local electronics store.

15. Failure to use a properly functioning surge 

suppressor could result in damage to the 

control system of the treadmill. If the control 

system is damaged, the walking belt may 

slow, accelerate, or stop unexpectedly, which 

may result in a fall and serious injury.

16. Keep the power cord and the surge suppres-

sor away from heated surfaces.

17. Never move the walking belt while the power 

is turned off. Do not operate the treadmill 

if the power cord or plug is damaged, or if 

the treadmill is not working properly. (See 

MAINTENANCE AND TROUBLESHOOTING 

on page 30 if the treadmill is not working 

properly.)

18. Read, understand, and test the emergency 

stop procedure before using the treadmill 

(see HOW TO TURN ON THE POWER on  

page 19). Always wear the clip while using the 

treadmill.

    WARNING:

 

To reduce the risk of burns, fire, electric shock, or injury to persons, read 

all important precautions and instructions in this manual and all warnings on your treadmill before 

using your treadmill. ICON assumes no responsibility for personal injury or property damage sus-

tained by or through the use of this product.

IMPORTANT PRECAUTIONS

Summary of Contents for PRO-FORM TRAINER 12.0









































Reviews: