background image

22

HOW TO ADJUST THE DRIVE BELT

If you can feel the pedals slip while you are pedaling,

even when the resistance is adjusted to the highest

level, the drive belt may need to be adjusted.

To adjust the drive belt, first unplug the power cord.

Using a flat screwdriver, release the tabs on the

Access Cover (20) and pry the Access Cover upward

off the elliptical exerciser.

Next, lift the Latch (50) on the underside of the Left

Pedal Arm (13), and then lift the Left Pedal Arm off the

left Pedal Arm Sleeve (46).

Then, remove the M4 x 16mm Round Head Screws

(152) and the M4 x 42mm Screws (153) from the

Right and Left Shields (18, 19). (Note: Not all Screws

are shown. Be sure to note which size Screws come

from which holes.) Then, carefully remove the Left

Shield.

Loosen the Pivot Screw (97). Tighten the Belt

Adjustment Screw (85) until the Drive Belt (38) is tight.

When the Drive Belt is tight, tighten the Pivot Screw.

When you are finished, reattach the left shield, replace

the left pedal arm, and reattach the access cover.

Then, plug in the power cord.

13

50

19, 18

153

153

152

46

85

38

97

20

Summary of Contents for PRO-FORM 890 E

































Reviews: