background image

20

   To pause the console, stop pedaling. When the 

console is paused, the displays will pause. To 

continue your workout, simply resume pedaling.

   To reset the displays to zero, press the On/Reset 

button.

  

Note: The console can show pedaling speed and 

distance in either miles or kilometers. To change 

the unit of measurement, see THE SETTINGS 

MODE on page 23.

5.   Measure your heart rate if desired. 

   You can measure your heart rate using either 

the handgrip heart rate monitor or a compatible 

heart rate monitor. For information about pur-

chasing an optional chest heart rate monitor, 

see page 22. 

   The console is compatible with all BLUETOOTH

®

 

Smart heart rate monitors. To connect your heart 

rate monitor to the console, see page 22.

   Note: If you use both heart rate monitors at the 

same time, the BLUETOOTH Smart heart rate 

monitor will have priority.

   If there are sheets of 

plastic on the metal 

contacts (A) on the 

handgrip heart rate 

monitor, remove the 

plastic. In addition, 

make sure that your 

hands are clean. To 

measure your heart 

rate, hold the handgrip 

heart rate monitor with 

your palms resting against the contacts. Avoid 

moving your hands or gripping the contacts 

tightly. 

   When your pulse is detected, your heart rate will be 

shown in the upper display. For the most accurate 

heart rate reading, hold the contacts for at least 

15 seconds. 

   If your heart rate is not shown, make sure that your 

hands are positioned as described. Be careful not 

to move your hands excessively or to squeeze the 

contacts tightly. For optimal performance, clean 

the contacts using a soft cloth; never use alcohol, 

abrasives, or chemicals to clean the contacts.

6.   When you are finished exercising, the console 

will turn off automatically.

  

 If the pedals do not move for several seconds, a 

series of tones will sound, the console will pause, 

and displays will pause.

   If the pedals do not move for several minutes, the 

console will turn off and the displays will be reset.

HOW TO USE THE SOUND SYSTEM

To play music or audio books through the console 

sound system while you exercise, plug a 3.5 mm male 

to 3.5 mm male audio cable (not included) into the 

jack on the console and into a jack on your personal 

audio player; make sure that the audio cable is fully 

plugged in. Note: To purchase an audio cable, see 

your local electronics store. 

Next, press the play button on 

your personal audio player. 

Adjust the volume level using 

the Vol increase and decrease 

buttons on the console or the 

volume control on your personal audio player.

A

Summary of Contents for PFEL03717.0

































Reviews: