manualshive.com logo in svg

Icom IC-M1V, Instruction Manual

Share
Download
Icom IC-M1V Instruction Manual Download Page 7

y

CHANNEL UP/DOWN SWITCHES [

Y

Y

]/[

Z

Z

]

➥

Push either switch to change the operating channel.
(pgs. 7–9)

➥

Checks tag channels or changes scanning direction dur-
ing scan. (p. 13)

➥

Push either switch to change the setting during set
mode. (p. 16)

u

CHANNEL 16 SWITCH [16•9]

➥

Selects channel 16 when pushed. (p. 7)

➥

Selects the call channel when pushed for 2 sec. (p. 7)

➥

Enters call channel write mode when the call channel is
selected, and this switch is pushed for 5 sec. (p. 11)

i

INTERNAL MICROPHONE (p. 9)

o

SPEAKER-MICROPHONE CONNECTOR [SP MIC]
Connects the optional speaker-microphone. (p. 22)

!0

ANTENNA CONNECTOR
Connects the supplied antenna. (p. 6)

!1

CHANNEL/WEATHER CHANNEL SWITCH
[CH/WX•U/I/C]

➥

Selects and changes the regular channels and weather
channel when pushed momentarily. (p. 8)

➥

Selects one of 3 regular channels in sequence when
pushed for 2 sec. (p. 8)

• U.S.A., International and Canadian channels are avail-

able for regular channels.

!2

DUALWATCH/TRI-WATCH SWITCH [DW•TRI]

➥

Starts dualwatch when pushed momentarily. (p. 14)

➥

Starts tri-watch when pushed for 2 sec. (p. 14)

➥

Stops dualwatch/tri-watch when either is activated.
(p. 14)

➥

Enters comment writing condition when pushed while
pushing and holding [MONI]. (p. 15)

!3

SCAN SWITCH [SCAN•TAG]

➥

Starts and stops normal or priority scan when tag chan-
nels are programmed. (p. 13)

➥

Sets the displayed channel as a tag (scanned) channel
when pushed for 2 sec. (p. 13)

➥

While turning power ON, clears all tag channels in the
selected regular channel group when pushed. (p. 13)

➥

Activates an optional voice scrambler function while
pushing [MONI]. (p. 10)

!4

TRANSMIT POWER/LOCK SWITCH [H/L•LOCK]

➥

Changes high and low power (1 W) when pushed. (p. 9)

• Some channels are set to low power only.

➥

While pushing [MONI], push this key to select extra low
power (500 mW). (p. 9)

➥

Changes the lock function ON and OFF when pushed
for 2 sec. (p. 10)

!56

INTERNAL SPEAKER

PANEL DESCRIPTION

3

2

Summary of Contents for IC-M1V

































Reviews:

No comments

Brands by name

Popular brands

Load more brands