manualshive.com logo in svg

Icom IC-M1V, Instruction Manual

Share
Download
Icom IC-M1V Instruction Manual Download Page 26

22

10

SPEAKER-MICROPHONE

■

Descriptions

NEVER immerse the connector in water. If the connector be-
comes wet, be sure to dry BEFORE attaching it to the trans-
ceiver.

NOTE: The microphone is located at the top of the
speaker-microphone, as shown in the diagram above. To
maximize the readability of your transmitted signal (voice),
hold the microphone approx. 2.5 cm (1 inch) from your
mouth, and speak in a normal voice level.

■

Attachment

Insert the connector of the speaker-microphone into the
[SP MIC] connector on the transceiver and rotate (screw) the
connector cover as shown in the diagram below. 

IMPORTANT: KEEP the [SP MIC] jack cover attached
(transceiver) when the speaker-microphone is not in use.
Water will not get into the transceiver even if the cover is
not attached, however, the terminals (pins) will become
rusty, or the transceiver will function abnormally if the con-
nector has become wet.

Alligator type clip
To attach the speaker-mic.
to your shirt or collar, etc.

PTT switch
Transmits during push
Receives during release

Microphone

Speaker

CAUTION: Attach the speaker-
microphone’s connector secure-
ly to prevent accidental drop-
ping, or water intrusion in the 
connector.

Summary of Contents for IC-M1V

































Reviews:

No comments

Brands by name

Popular brands

Load more brands