12
REMOTE CONTROL OPERATION
1
1-6 OPERATION EXAMPLE FOR PHONE PATCH
D
D
Description
Phone Patch function allows communication to a
transceiver from a telephone line, or connection to a
telephone line from a transceiver. During the Phone
Patch operation, the voice communication is sim-
plex. (The mute control is activated from the trans-
ceiver’s continuous tone SQL.)
■
Operation from the transceiver
One of two methods (Dial and Auto-dial) of telephone
access is selectable from the transceiver.
Dial: Direct dialing from the keypad of a transceiver.
Auto-dial: Using the pre-programmed phone No. (up
to 20 channels are stored) in the repeater.
D
D
TEL Dial (
0015 Default)
q
Enter the programmed password from transceiv-
er.
Code:
∗
0001#
• Verify the repeater replies “System Password OK
ACK (1111).”
• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.
w
Enter the “TEL Dial” command within 10 sec.
Code:
∗
0015#
• Verify the repeater replies “OK ACK (3333).”
• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:
∗
0001#0015#
).
e
Enter the telephone number (if the number is 060-
3355-2244) as sub code within 10 sec.
Code:
∗
06033552244#
• Verify the repeater replies “OK ACK (3333).”
• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:
∗
0001#0015#06033552244#
).
• The repeater starts calling the number.
r
When the connection has been confirmed, talk to
the phone by simplex voice communication.
t
After conversation is finished enter the password
followed by the “System Control Exit” command to
terminate Phone Patch operation.
Code:
∗
0001
#
0002#
• Verify the repeater replies “System Control Exit ACK
(2020),” then repeater hangs on the phone.
D
D
TEL Autodial (0016 Default)
Autodial number: 12 (Channel 12)
q
Enter the following DTMF codes.
Code:
∗
0001#0016#12#
• Verify the repeater replies “OK ACK (3333).”
• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and com-
mand code are correct, and try again.
• The repeater starts calling the autodial channel 12.
w
When the connection has been confirmed, talk to
the phone by simplex voice communication.
e
After conversation is finished enter the password
followed by the “System Control Exit” command to
terminate Phone Patch operation.
Code:
∗
0001
#
0002#
• Verify the repeater replies “System Control Exit ACK
(2020),” then repeater hangs on the phone.
■
Operation from the phone line
D
D
TX Start (0005 Default)
Step by step operation from the phone line.
q
Dial the phone number of the phone line that the
repeater is connected to.
w
When the connection has been confirmed, enter
the programmed password.
Code:
∗
0001#
• Verify the repeater replies “System Password OK
ACK (1111).”
• If the repeater replies “NG ACK (4040),” make sure
the password, header tone and de-limiter tone are
correct, and try again.
e
Enter the “TX Start” command within 10 sec.
Code:
∗
0005#
• Verify the repeater replies “OK ACK (3333).”
• If the 10 sec. input standby time runs out, enter the
password and command continuously (Code:
∗
0001#0005#
).
• The repeater starts the downlink transmission for
Phone Patch operation.
r
After conversation is finished, hang up the phone,
the repeater automatically disconnects the phone
and stops the downlink transmission.
D
D
TX Stop (0006 Default)
During Phone Patch operation this command stops
repeater from transmitting, for changing repeater settings.
q
Enter the following DTMF code (password and
command code).
Code:
∗
0001#0006#
• Verify the repeater replies “OK ACK (3333).”
• If the repeater replies “NG ACK (4040),” make sure
the password, header tone, de-limiter tone and TX
stop code are correct, and try again.
w
You may continue remote control operation from
the phone line to make other settings in the
repeater, or hang up the phone if there is nothing
else to change.
