background image

4

SAFETY TRAINING INFORMATION

18

W ARNING

Your Icom radio generates RF electromagnetic en-
ergy during transmit mode. This radio is designed 
for  and  classified  as  “Occupational  Use  Only”, 
meaning it must be used only during the course of 
employment by individuals aware of the hazards, 
and the ways to minimize such hazards. This radio 
is NOT intended for use by the “General Popula-
tion” in an uncontrolled environment.

•  For compliance with FCC and Industry Canada RF Exposure Re

-

quirements, the transmitter antenna installation shall comply with 

the following two conditions:

  1. The transmitter antenna gain shall not exceed 0 dBi.

  2. IC-F5121D:

 

 The antenna is required to be located outside of a vehicle and 
kept at a distance of 45 centimeters or more between the trans-
mitting antenna of this device and any persons during operation. 
For small vehicle as worst case, the antenna shall be located on 
the roof top at any place on the centre line along the vehicle in 
order to achieve 45 centimeters separation distance. In order to 
ensure this distance is met, the installation of the antenna must 
be mounted at least 45 centimeters away from the nearest edge 
of the vehicle in order to protect against exposure to bystanders.

  2. IC-F6121D:

 

 The antenna is required to be located outside of a vehicle and 
kept at a distance of 37 centimeters or more between the trans-
mitting antenna of this device and any persons during operation. 
For small vehicle as worst case, the antenna shall be located on 
the roof top at any place on the centre line along the vehicle in 
order to achieve 37 centimeters separation distance. In order to 
ensure this distance is met, the installation of the antenna must 
be mounted at least 37 centimeters away from the nearest edge 
of the vehicle in order to protect against exposure to bystanders.

  3. IC-F5121D:

 

 Transmit only when people outside the vehicle are at least the 
recommended minimum distance of 100 centimeters away from 
the properly installed antenna. This separation distance will en-
sure that there is sufficient distance from a properly installed 
externally-mounted antenna to satisfy the RF exposure require-
ments in the applicable RF exposure compliance standards.

  3. IC-F6121D:

 

 Transmit only when people outside the vehicle are at least the 
recommended minimum distance of 82 centimeters away from 
the properly installed antenna. This separation distance will en-
sure that there is sufficient distance from a properly installed 
externally-mounted antenna to satisfy the RF exposure require-
ments in the applicable RF exposure compliance standards.

Summary of Contents for IC-F6121D-51B





























Reviews: