background image

5

1

PANEL DESCRIPTION

HIGH/LOW KEY

Push to select the transmit output power temporarily or per-
manently, depending on the pre-setting.

• Ask your dealer for the output power level for each selection.

C.TONE CH ENT KEY

Push to select the continuous tone channel using [CH Up]/[CH
Down] to change the tone frequency/code setting after push-
ing this key. The selected channel remains set as the continu-
ous tone channel until another channel is designated as such.

TALK AROUND KEY

Push to turn the talk around function ON and OFF.

• The talk around function equalizes the transmit frequency to the

receive frequency for transceiver-to-transceiver communication.

WIDE/NARROW KEY

Push to toggle the IF bandwidth between wide and narrow.

• The wide passband width can be selected from 25.0 or 20.0 kHz

using the CS-F5060 

CLONING SOFTWARE

. (PMR or BIIS PMR opera-

tion only) Ask your dealer for details.

DTMF AUTODIAL KEY

Push to enter the DTMF channel selection mode. Then select
the desired DTMF channel using [CH Up]/[CH Down].
After selecting the DTMF channel, push again to transmit the
selected DTMF code.

RE-DIAL KEY

Push to transmit the last-transmitted DTMF code.

• TX memories are cleared after turning the transceiver OFF.

SCRAMBLER FUNCTION

Push to toggle the voice scrambler function ON and OFF.

CALL KEYS

Push to transmit a 2/5-tone/BIIS ID code.

• Call transmission is necessary before calling another station

depending on your signalling system.

• [Call A] and/or [Call B] may be available when your system employs

selective ‘Individual/Group’ calls. Ask your dealer which call is
assigned to each key.

EMERGENCY KEYS

Push and hold to transmit an emergency call.

When [Emergency Single (Silent)] or [Emergency Repeat
(Silent)] is pushed, an emergency call is transmitted with
no beep emission and LCD indication change.

• If you want to cancel the emergency call, push (or push and

hold) the key again before transmitting the call.

• The emergency call is transmitted one time only or repeatedly

until receiving a control code depending on the pre-setting.

SURVEILLANCE KEY

Push to turn the surveillance function ON or OFF.
When this function is turned ON, the beep is not emitted and
the LCD backlight and the LED indicator do not light when a
signal is received or a key is pushed.

COMPANDER KEY

Push to toggle the compander function ON and OFF. 
The compander function reduces noise components from the
transmitted audio to provide clear communication.

Summary of Contents for IC-F6062

























Reviews: