background image

4

SETTINGS

8

Setting the group code number

CTCSS tone setting

 

D

The transceiver is equipped with 50 CTCSS tones.
CTCSS operation enables silent standby, since you will 
only receive calls from group members using the same 
CTCSS tone.

Rotate 

 

q

[VOL]

 to turn OFF the power.

 Set 

 

w

[ROTARY  SELECTOR]

  to  any  channel  other 

than Channel 16.
 While  holding  down 

 

e

[PTT]

[Upper]

,  and 

[Lower]

rotate 

[VOL]

 to turn ON the power.

 Rotate 

 

r

[ROTARY SELECTOR]

 to select the desired 

channel (1 to 16) that you want to assign the CTCSS 
tone to.
 Hold down 

 

t

[Upper]

 until two beeps sound.

  •  The transceiver enters the CTCSS tone setting mode.

 Push 

 

y

[PTT]

 the necessary number of times to enter 

the  ten’s  digit  of  the  desired  CTCSS  tone  number 
(grey column) as shown in the list below.
Push 

 

u

[Upper]

.

  • The selected number will be announced.

 Push 

 

i

[PTT]

 the necessary number of times to enter 

the  one’s  digit  of  the  desired  CTCSS  tone  number 
(grey column) as shown in the list below.
 Push 

 

o

[Upper]

 to complete the setting.

  • The selected number will be announced.

!0

  Turn OFF the power to exit the CTCSS tone setting 

mode.

NOTE:

•  If you make a mistake, go back to step 

q

 and follow 

all the steps again.

•  If you want to enter “0,” do not push 

[PTT]

 in step 

t

 

and 

u

, just push 

[Upper]

. Then “zero” will be an

-

nounced. To turn OFF the CTCSS tone, enter “00.”

[Example]:

  CTCSS  tone  No.  28  (162.2  Hz)  assigned 

to channel 4

Rotate 

 

q

[VOL]

 to turn OFF the power.

 While  holding  down 

 

w

[PTT]

[Upper]

,  and 

[Lower]

rotate 

[VOL]

 to turn ON the power.

  •  The transceiver enters CTCSS tone Setting mode.

 Rotate 

 

e

[ROTARY SELECTOR]

 to select channel 4, 

then hold down 

[Upper]

 until two beeps sound.

 Push 

 

r

[PTT]

 two times to enter “2” (the ten’s digit) of 

the number 28.
Push 

 

t

[Upper]

.

  • “Two” will be announced.

 Push

 

y

 [PTT]

 eight times to enter “8” (the one’s digit) 

of the number 28.
Push 

 

u

[Upper]

 to complete the setting.

  • “Eight” will be announced.

Turn OFF the power to set the CTCSS tone.

 

i

[ROTARY SELECTOR]

[VOL]

[Lower]

[Upper]

[PTT]

• Available CTCSS tone list 

(Hz)

No. Freq. No. Freq. No. Freq. No. Freq. No. Freq.

01
02
03
04
05
06
07
08
09
10

67.0
69.3
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5

11
12
13
14
15
16
17
18
19
20

94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3

21
22
23
24
25
26
27
28
29
30

131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9

31
32
33
34
35
36
37
38
39
40

171.3
173.8
177.3
179.9
183.5
186.2
189.9
192.8
196.6
199.5

41
42
43
44
45
46
47
48
49
50
00

203.5
206.5
210.7
218.1
225.7
229.1
233.6
241.8
250.3
254.1
OFF

Summary of Contents for IC-F29SR















Reviews: