background image

Limited Warranty

Coverage:

Link Communications Inc. warrants that its products will be free from defects in materials and
workmanship for a period of one year from the date of shipment.  During this time, Link
Communications Inc. will cover parts, labor and return shipping.  If failure is caused by
instances other than manufacturing defects, Link Communications Inc. will repair the product
and bill the customer for parts, labor, and shipping. Contact Link Communications Inc. for more
information.

What Link Communications Inc. will not cover:

1.  Too much voltage to the controller.  The RLC-ICM operates at +11V to +15V, negative
ground.

2.   Damage to the controller by lightning, accident, or incorrect power hook-up.

3.   Incorrect unit installation.

4.   Damage caused by shipment (damage claims are handled by the carrier).

6.   Repairs by other than Link Communications Inc.

THIS WARRANTY HOLDS ONLY TO THE ORIGINAL PURCHASER

HOW TO GET SERVICE

Please contact Link Communications Inc. for servicing information and authorization.

SOFTWARE

Link Communications Inc. holds the copyright on the RLC-ICM's software and hardware. 
Changes to the software and copying of the software is prohibited without the written consent of
Link Communications Inc.  

Summary of Contents for IC-900


























Reviews: