ICM Controls S166 Installation And Operation Instruction Manual Download Page 7 | Manualshive

Page: 7 / 16

background image

ELECTRONIC CIRCULATOR FOR SOLAR THERMAL SYSTEMS - Art. S166

FI.S166.EN.C - 10/2022

Icma SpA - Via Garavaglia, 4 - 20012 Cuggiono (MI) ITALY Tel: +39 02 97249134 - +39 02 97249135 - www.icmaspa.it - [email protected]

Icma SpA - Via Garavaglia, 4 - 20012 Cuggiono (MI) ITALY Tel: +39 02 97249134 - +39 02 97249135 - www.icmaspa.it - [email protected]

6

7

Ambient temperature

Liquid temperature

[°C]

Min. [°C]

Max. [°C]

To avoid condensation in the motor and the electronics the temperature of the pumped liquid must always be
greater than the ambient temperature.

«
...
5
6
7
8
9
...
»

Summary of Contents for S166

















Reviews:

No comments

Related manuals for S166

Brand: Camlite Video Systems Pages: 7

Brand: Harman Kardon Pages: 32

Brand: Harman Kardon Pages: 73

Brand: Harman Kardon Pages: 30

Brand: Harman Kardon Pages: 2

Brand: Harman Kardon Pages: 10

Brand: Q-Pumps Pages: 44

Brand: SAER Elettropompe Pages: 76

Brand: A.O. Smith Pages: 6

Brand: GE Pages: 1

Brand: Onkyo Pages: 2

Panacom PANAIP7GM

Brand: PSA Pages: 10

Wave SoundTouch IV series

Brand: Bose Pages: 32

Brand: Q-See Pages: 9

VM9212N - Multimedia CD/DVD Receiver

Brand: Jensen Pages: 32

COMAND AND REAR-CABIN AUDIOVISUAL SYSTEM

Brand: MAYBACH Pages: 319

Vingtor Stentofon SPA-AC6

Brand: Zenitel Pages: 54

Brand: M-system Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands