background image

 

 

 

 

308DUO V1.1.0 

Synchronous  Balance  Charger/Discharger

 

 

- 31 - 

 

Extra Function

 

 

Log Files Manage 

Select 

SYSTEM MENU

Extra Function

LOG FILES 

to enter the manage interface. 

                   

 

First select and click the .TXT files when managing log files, and the system will pop up the

 LOG FILES OP 

dialog box. 

                   

 

Select 

Delete

 to pop up the 

LOG FILE DELETE 

dialog

 

box, Select 

Yes 

to delete this file, select 

No 

to cancel. 

                   

   

 

Servo Test 

Select 

SYSTEM MENU

Extra Function

SERVO TEST 

to enter servo test interface; insert Servo into 

J1 

or

 J2 

port to 

test (only 

J1

 port supports Speed Test, 

J2 

can also be used as an external power source).   

                   

               

Log Files Manage Dialog 

  Transmission: transmission to PC 

  Delete: delete files 

  Delete All: delete all files 

The  charger  must  be  connected  with  computer  via 

USB  when  select 

Transmission

  and  the  client 

software must have identified to the

 

charger.

 

 

 

   

Type:

 

Analog servo (1500us/50Hz) 

              Digital servo (1500us/333Hz) 

              Digital servo (760us/560Hz) 

              User: Pulse Center: 700us-1600us 

                        Frame Rate: 40Hz-700Hz 

                        45

°

Pulse Traveling:100us-1000us

 

 

Summary of Contents for 308DUO











































Reviews: