background image

15

7. Guide to Operating the Ice Maker

Fig. 10 Switch

Fig. 11 Ice cube

Initial operation

① Open the water supply valve connected with the ice maker.
② Insert the plug of the ice maker into the electric outlet.
③ Open the door and turn the switch at the lower end of the
   product to the “ICE” position.”
④ Discard the first batch of ice.
⑤ Good-quality ice is produced 1-2 hours later.

Using the ice maker

Use of the ice maker is very simple. Simply turn the switch at
the lower end of the product to the “ICE” position. 
The product automatically starts ice production, which continues
until the ice container has been filled with ice. Remove the ice 
using an ice gourd and insert the gourd into the holder on the 
inside of the container (If you place the container in the ice, 
it may be covered over by ice).

The ice maker produces 24 pieces of ice every 30 minutes. 

Also, the produced ice drops down into the ice container; 

water is supplied to the ice maker and the water is also 

drained.

Important Information : 

Do not put anything other than 

ice in the ice container. Wine or beer bottles are unsanitary 

and a detached label may block the drain pipe.

Ice

The ice has a rectangular bell shape (refer to the figure). 
Newlyproduced ice is clear and transparent. The inside of the ice 
is sometimes cracked; however, such cracks commonly occur in
the production process and disappear with time.
Ice stored in the container for a long time may gather frost on
the outside and look muddy. This is normal ice and, once water
is poured on the ice, such frosting disappears.

Ice container

The product continues making ice until the level of ice reaches
the temperature sensing tube(right side). It then ceases operation.
The model with a drain pump drains away melted ice when the
ice maker is turned off. The pump works for only several seconds.

Summary of Contents for A25B15O





























Reviews: