ICE TECH PS
14
a) WATER IMPURITIES: Major impurities are eliminated by filters provided. Filters should be
cleaned regularly depending on purity of water. For minor impurities we recommend installing a
5-micron filter. (Provided with the unit: Part # ICE TECH 207499).
b) WATER WITH MORE THAN 500 PPM:
deposits may impede proper function. In water cooled models, condenser obstruction is likely.
Installation of a high quality water softener is recommended. (Code ICE TECH 207500).
a) c) CHLORINATED WATER:
ICE TECH 207509).
(NOTE: You may encounter water with
d) PURIFIED WATER: A 10% reduction in overall production may occur.
4.3. Connecting unit to water source (water
• Use 1.3 m. flexible tube (with the two filters attached) provided. NOTE: We advise using a
single faucet fixture.
• Water pressure should be between 0.7 and 6 Kgs/cm2. (10/85 Psi.)
• If water pressure exceeds these values, installation of appropriate corrective units will be
necessary.
• It is important that water tubing does not come close to or in contact with any
or heat generated by unit as this could decrease production.
4.4. Connecting unit to drain (water
• Drain must be located at least 150mm below machine level. Drain tube must have an inner
diameter of 30mm and a minimum gradient of 3
4.5. Electrical connection
• Unit is provided with a 1.5 m cord and Schucko soc
• It is recommended to install a switch and adequate fuses. Nominal voltage and intensity are
indicated on rating plate as well as on this manual. Voltage f
cause problems or prevent machine from starting.
• Line to base of plug must have a mínimum 12/10 section in the small models and 25/10 in the
big ones.
• Be sure that voltage indicated on rating plate corresponds to that
ICE TECH PS Technical Service Manual
Major impurities are eliminated by filters provided. Filters should be
cleaned regularly depending on purity of water. For minor impurities we recommend installing a
(Provided with the unit: Part # ICE TECH 207499).
WATER WITH MORE THAN 500 PPM: Ice will be less hard and tend to adhere. Lime
deposits may impede proper function. In water cooled models, condenser obstruction is likely.
quality water softener is recommended. (Code ICE TECH 207500).
CHLORINATED WATER: Chlorine taste can be avoided by installing a carbon filter (Code
(NOTE: You may encounter water with ALL aforementioned properties.)
A 10% reduction in overall production may occur.
Connecting unit to water source (water-cooler units)
• Use 1.3 m. flexible tube (with the two filters attached) provided. NOTE: We advise using a
• Water pressure should be between 0.7 and 6 Kgs/cm2. (10/85 Psi.)
• If water pressure exceeds these values, installation of appropriate corrective units will be
• It is important that water tubing does not come close to or in contact with any
or heat generated by unit as this could decrease production.
Connecting unit to drain (water-cooled models)
• Drain must be located at least 150mm below machine level. Drain tube must have an inner
diameter of 30mm and a minimum gradient of 3 cm per metre.(3%)
Electrical connection
• Unit is provided with a 1.5 m cord and Schucko socket.
It is recommended to install a switch and adequate fuses. Nominal voltage and intensity are
indicated on rating plate as well as on this manual. Voltage fluctuations greater than 10% can
cause problems or prevent machine from starting.
Line to base of plug must have a mínimum 12/10 section in the small models and 25/10 in the
voltage indicated on rating plate corresponds to that of mains supply.
Technical Service Manual
Major impurities are eliminated by filters provided. Filters should be
cleaned regularly depending on purity of water. For minor impurities we recommend installing a
Ice will be less hard and tend to adhere. Lime
deposits may impede proper function. In water cooled models, condenser obstruction is likely.
quality water softener is recommended. (Code ICE TECH 207500).
Chlorine taste can be avoided by installing a carbon filter (Code
aforementioned properties.)
A 10% reduction in overall production may occur.
• Use 1.3 m. flexible tube (with the two filters attached) provided. NOTE: We advise using a
• Water pressure should be between 0.7 and 6 Kgs/cm2. (10/85 Psi.)
• If water pressure exceeds these values, installation of appropriate corrective units will be
• It is important that water tubing does not come close to or in contact with any heat sources
• Drain must be located at least 150mm below machine level. Drain tube must have an inner
It is recommended to install a switch and adequate fuses. Nominal voltage and intensity are
luctuations greater than 10% can
Line to base of plug must have a mínimum 12/10 section in the small models and 25/10 in the
of mains supply.