background image

 

13 

 

 

 

Rev. 1 

 

Trouble Shooting Checklist 

 

Model No: 

  

  

Serial 
Number: 

  

  

Voltage Rating: 

Amps: 

   Phase:  1 

   Frequency: 

Options: 

     

     

     

  

Is proper electrical power available at the power supply? 

Yes 

 

No 

 

Is your power cord connected to the power supply and IQ terminal block? 

Yes 

 

No 

 

Is the thermostat set-point temperature below the enclosure temperature? 

Yes 

 

No 

 

Is the evaporator (cold air stream) blower operating? 

Yes 

 

No 

 

Is the compressor and condenser (warm air stream) blower operating? 

Yes 

 

No 

 

Is the enclosure door closed tightly? 

Yes 

 

No 

 

Are all of the gaskets in place? 

Yes 

 

No 

 

Has the condenser (warm air stream) filter been cleaned or changed recently? 

Yes 

 

No 

 

Is the system mounted level on the enclosure? 

Yes 

 

No 

 

Is there adequate space within the enclosure for air flow? 

Yes 

 

No 

 

Is there adequate space around the air conditioner for airflow? 

Yes 

 

No 

 

Has the enclosure population remained the same? 

Yes 

 

No 

 

Notes: 

     

     

     

  

 

 

 

 

 

 

 

 

For additional support call: 

Ice Qube at 1-888-867-8234 

Please have above checklist completed before you call. 

Summary of Contents for EX series


























Reviews: