background image

The descriptions contained in this document are not binding.  

The company therefore reserves the right to make any modifications at any time to elements, 

details, or the supply of accessories, as considered necessary for reasons of improvement or 

manufacturing/commercial requirements. 

The reproduction, even partial, of the text and drawings contained in this document is prohibited 

by law. 

The company reserves the right to make any technical and/or supply modifications. The images 

are for reference purposes only, and are not binding in terms of design and supply. 

Symbols used in the manual 

Open book symbol with an "i" 

Indicates the need to consult the instruction manual 

Open book symbol 

Used to tell the operator to read the manual before using the machine 

Warning symbol 

Carefully read the sections marked with this symbol and observe the 

indications, for the safety of the operator and the machine 

Warning symbol 

Indicates danger of gas fumes and the leakage of corrosive liquids 

Warning symbol 

Danger of fire: do not go near with free flames 

Disposal symbol 

Carefully read the sections marked with this symbol for machine 

disposal 

Summary of Contents for SCRUB 35C





























Reviews: