background image

SAFETY AND WARNINGS BEFORE YOU BEGIN

 

WARNING: WHEN INSTALLING THIS GAME, A GROUNDED A.C. RECEPTACLE MUST BE USED. FAIL-
URE TO DO SO COULD RESULT IN INJURY TO YOURSELF OR OTHERS. FAILURE TO USE A 
GROUNDED RECEPTACLE COULD ALSO CAUSE IMPROPER GAME OPERATION, OR DAMAGE TO 
THE ELECTRONICS.

 

NOTE: THIS GAME IS INTENDED FOR INDOOR USE ONLY.

 

DO NOT DEFEAT OR REMOVE THE GROUNDING PRONG ON THE POWER CORD FOR THE SAME 
REASON AS GIVEN ABOVE. USING AN IMPROPERLY GROUNDED GAME COULD VOID YOUR WAR-
RANTY.

 

HAVE A QUALIFIED ELECTRICIAN CHECK YOUR A.C. RECEPTACLE TO BE SURE THE GROUND IS 
FUNCTIONING PROPERLY.

 

THIS GAME IS DESIGNED TO DISSIPATE STATIC ELECTRICITY THROUGH THE GROUNDING PLANE 
OF THE GAME. IF THE A.C. GROUND DOES NOT WORK, THE GAME COULD DISCHARGE STATIC 
ELECTRICITY THROUGH THE GAME CIRCUITRY, WHICH COULD CAUSE DAMAGE.

 

THE POWER SUPPLY IS NOT VOLTAGE ADJUSTABLE. TO OPERATE THE GAME AT VOLTAGES OTH-
ER THAN THOSE IT WAS DESIGNED FOR. PLEASE CONTACT OUR SERVICE DEPARTMENT FOR 
VOLTAGE CONVERSION INFORMATION.

 

WARNING

 

DO NOT remove any of the components on the main board (e.g. compact flash and eproms) while 
the game is powered on. This may cause permanent damage to the parts and the main board. Re-
moving any main board component part while powered on will void the warranty.

 

ALWAYS REMOVE POWER TO THE GAME, BEFORE ATTEMPTING ANY SERVICE,

 

UNLESS NEEDED FOR SPECIFIC TESTING.  FAILURE TO OBSERVE THIS PRECAUTION

 

COULD RESULT IN SERIOUS INJURY TO YOURSELF OR OTHERS.

 

THIS  GAME  IS  NOT  SUITABLE  FOR  INSTALLATION  IN  AN  AREA  WHERE  A  WATER  JET  COULD  BE 
USED.

 

This appliance is not intended for use by persons (including children) with reduced physical, sensory or men-
tal capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction 
concerning use of the appliance by a person responsible for their safety.

 

 Children should be supervised to 

ensure that they do not play with the appliance.

 

AC Power Information

 

The  games main fuse  is accessed through  the back  of  the  game at  the  power  mod.   Above  the 
power cord is a small panel that contains the main fuse.  

 

The value of the fuse for 120 volt users is 3 AMPS at 250Volt type slow blow.  

 

Summary of Contents for Hoopla


























Reviews: