background image

July 2013

Page 3

User Manual for Models HISU055, HISU075, HISU095

Pre-Installation

This appliance is intended to be used in commercial 
applications including:

• 

Restaurant kitchens

• 

Bars

• 

Hotels

Dimensions and Electrical:

Location: 

The unit can be built into a cabinet as the air flow is in 

and out the front.  The front of the machine must not 
be blocked. Certain maintenance or repair procedures 
will require removal of the top, back and side panels, 
so plan ahead for service and maintenance needs.

Spacing:

No additional spacing is required at the top or sides. 
However, suggested minimum side clearance for 
installation is 1/8 inch or 3 mm and suggested 
minimum top clearance is 1/4 inch or 7 mm. 

Allow 2 inches (50 mm) minimum space at the back 
for the utility connections. Do not block louvers at the 
front of the cabinet.

Unpacking and setup

Remove all shipping and packing materials that may 
be in the ice storage bin. 

The unit can be installed with or without legs. The 
cabinet is equipped with small bumpers on the base 

to allow placement without legs. An optional floor 

mounting kit is also available to fill the gap between 

the machine and floor if not using legs. If using legs, 

carefully tip the machine and install the legs by 
screwing them into the leg sockets in the bottom of 
the machine. For reference, the thread size is 5/8 – 
11. If the machine has been tipped onto its side or 
back allow 1 hour before starting the unit for the oil in 
the refrigeration system to return to the compressor.

Place the machine in its intended location and level it 
front to back and left to right. If using legs, adjust their 
feet in and out to level the cabinet.

If legs are not used the bottom edges of the cabinet 

must be sealed to the floor.

If built into a cabinet, the adjacent cabinet walls will 
provide the means for containment. There are no 
means for attachment to the cabinet.

Model

Electrical 
(volts/Hz/Phase

Width
(in / cm)

Depth
(in/cm)

Height
(in/cm)

Total Load 
Amps

HISU055FA

230/50/1

15 / 38

23.7 / 60.3

31.9 / 81.1

4

HISU075FA

230/50/1

15 / 38

23.7 / 60.3

31.9 / 81.1

4

HISU095FA

230/50/1

20 / 51

23.7 / 60.3

31.9 / 81.1

4

Air IN

Air OUT

Summary of Contents for HISU055


















Reviews: