background image

3

Using Ice Paddle Accessory 

The Ice Paddle is an optional accessory that can be ordered 

directly from Ice-O-Matic.  Mount the Ice Paddle for easy access on 

either side of the bin in the bracket provided. 

Using 

the Paddle

If there is adequate ice in bin but lower door area is not filled with 

ice, it may be that ice has congealed in bin and cannot flow. This 

can often be remedied by quickly jiggling the Ice Shield several 

times (Fig. 1). If problem continues, the Ice Paddle can be inserted 

through rectangular openings  in the Ice Shield and agitated back 

and forth to break up congealed ice mass (Fig. 2). 

Note:

 Use Ice Paddle only as described above. To avoid possible 

injury, keep head and face clear of lower door area and Ice Paddle 

at all times. Do not use the Ice Paddle for other purposes. 

Fig. 2

Technical assistance available toll free 

Should  you have any questions  concerning  installation or maintenance of Ice-O-Matic ice storage bins, please 

call our technical service department at 800 423-3367 (US & Canada) between 7:30 a.m. and 4:00 p.m. 

Mountain time.

Cleaning

Interior of bin must be cleaned and sanitized prior to use and should be cleaned on routine basis during use. 

Interior Bin Care 

Ice-O-Matic single door upright ice storage bins are equipped with polyethylene liner walls and stainless steel 

bottoms which should be cleaned and sanitized periodically with any product suitable for use in a food zone. 

 

Important: Ice-O-Matic recommends installing our IFQ Water Filter on water supply to icemaker to 

remove chlorine. 

1.  Remove upper inspection windows by sliding windows to one side. Grasp the end of the front window and pull 

toward you as the window is slid to the opposite side. Repeat for rear window. 

Rear Window

Front Window 

2. Wash bin walls, hopper, access door plate and partition (if any), rinse and sanitize. 

Exterior Bin Care

Exterior stainless steel surfaces can be cleaned with a stainless steel cleaner such as 3M Stainless Steel 

Cleaner & Polish or equivalent. 

3

 

Summary of Contents for B1000-48













Reviews: