IC Realtime ICIP-D2000-VIR User Manual Download | Manualshive

Page: 18 / 31

background image

12

3

Installation

Important



Before you complete the installation and setup, do not remove the electrostatic attraction

film on the transparent enclosure. Otherwise it may result in injury.



After remove electrostatic attraction film, do not touch dome enclosure in case it may leave

stain.



Before the installation, please make sure the installation surface can sustain at least 3X

weight of the bracket and the camera.

3.1

Device Installation Introduction

Please refer to Figure 3-1 for device installation space information. You can use screws (diameter is less

than 4.5mm) to secure the device. You can see there are installation position map and installation

screws in the accessories bag for you to install the device conveniently.

Figure 3-1 Installation 1

3.2

Device Installation Steps

3.2.1 General Installation

The general interface is shown as in Figure 3-2.

«
...
16
17
18
19
20
...
»

Summary of Contents for ICIP-D2000-VIR
































Reviews:

No comments

Related manuals for ICIP-D2000-VIR

SECURICAM Network DCS-900

Brand: D-Link Pages: 92

SECURICAM Network DCS-900

Brand: D-Link Pages: 20

SECURICAM Network DCS-2120

Brand: D-Link Pages: 25

SECURICAM DCS-910

Brand: D-Link Pages: 7

Brand: D-Link Pages: 12

Brand: D-Link Pages: 4

Brand: D-Link Pages: 32

Brand: D-Link Pages: 8

DCS-6620G - Network Camera

Brand: D-Link Pages: 16

Brand: D-Link Pages: 8

Brand: D-Link Pages: 7

Brand: D-Link Pages: 24

Brand: D-Link Pages: 110

Brand: D-Link Pages: 66

Brand: D-Link Pages: 9

Brand: D-Link Pages: 4

Brand: D-Link Pages: 6

WIRELESS G DCS-950G

Brand: D-Link Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands