IBT Technologies MI979 Series User Manual Download

Page: 74 / 87

MI979 Series

User’s Manual

4.7 Boot Settings

BIOS Setting

Description

Setup Prompt
Timeout

Number of seconds to wait for setup activation
key.

65535 (0xFFFF) means indefinite waiting.

Bootup NumLock
State

Selects the keyboard NumLock state.

Quiet Boot

Enables / Disables Quiet Boot option.

Fast Boot

Eables / Disables boot with initalization of a
minimal set of devices required to launch active
boot option. This has no effect for BBS boot
options.

Boot mode select

Selects a Boot mode, Legacy / UEFI / Dual.

Boot Option Priorities

Sets the system boot order priorities for hard
disk, CD/DVD, USB, Network.

Hard Disk Drive BBS
Priorities

Specifies the Boot Device priority sequence from
available hard disk drives.

Summary of Contents for MI979 Series
























































































Search results

Summary of Contents for MI979 Series

Reviews:

Related manuals for MI979 Series

Brands by name

Popular brands

IBT Technologies MI979 Series, User Manual

Search results

Summary of Contents for MI979 Series

Reviews:

Related manuals for MI979 Series

Brands by name

Popular brands