IBT Technologies MI979 Series User Manual Download Page 67

Page: 67 / 87

BIOS Setup

MI979 Series

User’s Manual

4.4.8

CSM Configuration

BIOS Setting

Description

CSM Support

Enables / Disables CSM support.

GateA20 Active

•

Upon Request

disables GA20 when using

BIOS services.

•

Always

cannot disable GA20, but is useful

when any RT code is executed above 1 MB.

Option ROM
Messages

Sets the display mode for the Option ROM.
Options: Fore BIOS / Keep Current.

INT19 Trap Response Sets how BIOS reacts on INT19 trap by Option

ROM.

•

Immediate

executes the trap right away.

•

Postponed

executes the trap during legacy

boot.

Boot option filter

Controls the priority of Legacy and UEFI ROMs.

Options: UEFI and Legacy / Legacy only / UEFI
only

Network

Contrls the execution of UEFI and Legacy PXE
OpROM.

Options: Do not launch / Legacy

Summary of Contents for MI979 Series
























































































Search results

Summary of Contents for MI979 Series

Reviews:

Related manuals for MI979 Series

Brands by name

Popular brands

IBT Technologies MI979 Series, User Manual

Search results

Summary of Contents for MI979 Series

Reviews:

Related manuals for MI979 Series

Brands by name

Popular brands