IBM WDA L160 Manual Download Page 3

IOCHRDY is set to on (ie, jumper on pins 1-2) 
Device ID is set to Master (ie, jumper on pins 3-4) 

Note: 

 LED connections, pin 13 can source up to 18mA. Pin 14 can sink up to 100mA.

Data Organization

Physical Layout      

          WDA-L80          WDA-L160 

Bytes per Sector                     512                      512 
Total Data Sectors              167301                334602 
Total Data Bytes               85,658,112       171,316,224 
BIOS Capacity of Drive (MB {sectors x 512})    

             *                         * 

Sectors per Track                    44                       44 
Sectors per Cylinder                87                     174 
Spare Sectors per Cylinder       1                        2 
Numbers of Data Heads           2                        4 
Numbers of Disks                    1                        2

Logical Layout 

Logical Heads                        10                      10
Sectors/Track                         17                      34 
Logical Cylinders                  984                   984

Operating Environment 

Humidity 

Operating Relative            8% to 90% noncondensing
 Nonoperating Relative     5% to 95% noncondensing

Wet Bulb Temperature: 

Maximum Wet Bulb: 
Operating                       29.4 degrees Centigrade non-condensing 
Non-operating                35.0 degrees Centigrade non-condensing

Elevation: 

Operating Altitude         -150 to 3000m 
Ship/Storage Altitude     -150 to 12000m

Temperature:

Operating                        5 to 55 degrees Centigrade 
Storage                          -40 to 65 degrees Centigrade 
Shipping                        -40 to 65 degrees Centigrade 
Temperature Gradient    15 degrees Centigrade per hour (maximum)
 (Operating, Storage and Shipping)

Summary of Contents for WDA L160










Reviews: