2.
Loosen
wing
nuts
2
and
3
.
3.
Slide
the
bracket
toward
the
back
of
the
rail.
4.
Remain
at
the
back
of
the
rack,
hold
the
support
rail
in
position
in
the
rack,
and
then
install
and
fully
tighten
the
two
mounting
screws
5
.
5.
Go
to
the
front
of
the
rack.
6.
Extend
the
support
rail
toward
the
front
of
the
rack.
Note:
Hold
the
support
rail
in
position
until
you
have
completed
step
7.
Ensure
that
the
support
rail
is
horizontal.
You
may
want
to
use
a
level
to
ensure
the
support
rail
is
straight.
8.
Install
the
two
mounting
screws
1
into
the
third
and
fourth
holes
of
the
support
rail
flange.
Fully
tighten
the
screws.
9.
Fully
tighten
the
two
wing
nuts
shown
as
2
in
the
figure.
10.
With
wing
nut
3
still
loosened,
slide
the
bracket
toward
the
front
of
the
rail,
as
far
as
it
will
go,
with
the
front
edge
of
the
bracket
against
the
back
end
of
the
front
support
rail.
Fully
tighten
the
wing
nut
3
.
Installing
the
uninterruptible
power
supply
5115
in
the
rack
After
you
have
completed
the
preparation
procedures,
you
are
ready
to
install
the
uninterruptible
power
supply
(UPS)
5115
in
the
rack.
You
must
complete
the
following
prerequisites
before
installing
the
UPS
5115
in
the
rack:
v
Complete
the
preinstallation
procedures.
v
Install
the
support
rails
for
the
UPS
5115.
v
Prepare
your
UPS
5115
environment.
Attention:
Read
all
safety
and
environmental
notices
before
starting
the
installation
process.
CAUTION:
The
UPS
5115
contains
its
own
energy
source
(sealed,
lead-acid
batteries).
The
output
receptacles
may
carry
live
voltage,
even
when
the
UPS
5115
is
not
connected
to
an
AC
supply.
(11)
CAUTION:
Do
not
remove
or
unplug
the
input
cord
when
the
UPS
5115
is
turned
on.
This
removes
the
safety
ground
from
the
UPS
5115
and
the
equipment
connected
to
the
UPS
5115.
(12)
CAUTION:
To
reduce
the
risk
of
fire
or
electric
shock,
install
the
UPS
5115
in
a
temperature-
and
humidity-controlled
indoor
environment,
free
of
conductive
contaminants.
Ambient
temperature
must
not
exceed
40°C
(104°F).
Do
not
operate
near
water
or
excessive
humidity
(95%
maximum).
(13)
Chapter
3.
Installing
the
uninterruptible
power
supply
and
the
SAN
Volume
Controller
37
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Summary of Contents for TotalStorage SAN Volume Controller
