IBM PS/2 25 SX Hardware Maintenance Reference Download Page 22 | Manualshive

Page: 22 / 37

IBM PS/2 25 SX Hardware Maintenance Reference Download Page 22

11.1 RPL Error Conditions for Ethernet

The following is a list of possible error conditions that can occur when

the workstation is attempting to connect to the network:

+------------------------------------------------------------------------+

¦ Problem ¦ Action ¦

+------------------------------------+-----------------------------------¦

¦ ET--00:00:02 ¦ If the elapsed time indicator ¦

¦ Field stops incrementing ¦ stops incrementing, check that: ¦

¦ ¦ 1. All cables and cords are ¦

¦ ¦ properly attached to the ¦

¦ ¦ workstation. ¦

¦ ¦ 2. The address for the network ¦

¦ ¦ adapter was properly added to ¦

¦ ¦ the network software. ¦

¦ ¦ 3. The adapter configuration ¦

¦ ¦ (BNC/UTP) is set properly. ¦

¦ ¦ 4. The server is operational. ¦

¦ ¦ ¦

¦ ¦ If the above items are correct, ¦

¦ ¦ restart the workstation. ¦

¦ ¦ If the problem remains, replace ¦

¦ ¦ the Ethernet adapter. ¦

+------------------------------------+-----------------------------------¦

¦ RQ--XXXX ¦ If a number greater than 000A ¦

¦ Field appears and XXXX is a value ¦ appears, the file server is not ¦

¦ greater than 000A ¦ present or is overloaded. Check ¦

¦ ¦ that: ¦

¦ ¦ 1. The server is available and ¦

¦ ¦ fully operational. ¦

¦ ¦ 2. The address for the network ¦

¦ ¦ adapter was properly added to ¦

¦ ¦ the network software. ¦

¦ ¦ 3. The adapter configuration ¦

¦ ¦ (BNC/UTP) is set properly. ¦

¦ ¦ ¦

¦ ¦ If the above items are correct ¦

¦ ¦ and the problem remains, replace ¦

¦ ¦ the Ethernet adapter. ¦

+------------------------------------+-----------------------------------¦

¦ SF--XXXX ¦ If a number greater than 000A ¦

¦ Field appears and XXXX is a value ¦ appears, the server was found, ¦

¦ greater than 000A ¦ but is not responding. Check ¦

¦ ¦ that: ¦

¦ ¦ 1. The server is available and ¦

¦ ¦ fully operational. ¦

¦ ¦ 2. The address for the network ¦

¦ ¦ adapter was properly added to ¦

¦ ¦ the network software. ¦

¦ ¦ ¦

¦ ¦ If the above items are correct ¦

¦ ¦ and the problem remains, replace ¦

¦ ¦ the Ethernet adapter. ¦

+------------------------------------------------------------------------+

IBM PS/2 Model 25 SX HMR

RPL Error Conditions for Ethernet

¦ Copyright IBM Corp. 1992

11.1 - 1

«
...
20
21
22
23
24
...
»

Summary of Contents for PS/2 25 SX






































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands