manualshive.com logo in svg

IBM Power 750 Express, Technical Overview And Introduction

Share
Download
IBM Power 750 Express Technical Overview And Introduction Download Page 15

© Copyright IBM Corp. 2013. All rights reserved.

1

Chapter 1.

General description

The IBM Power 750 Express server (8408-E8D) and IBM Power 760 server (9109-RMD) use 
the latest  processor technology that is designed to deliver unprecedented 
performance, scalability, reliability, and manageability for demanding commercial workloads.

The IBM Power 750 Express server and the Power 760 server deliver the outstanding 
performance of the  processor. The performance, capacity, energy efficiency, and 
virtualization capabilities of the Power 750 or Power 760 make it an ideal consolidation, 
database or multi-application server. As a consolidation or highly virtualized multi-application 
server, the Power 750 Express and the Power 760 servers offer tremendous configuration 
flexibility to meet the most demanding capacity and growth requirements. Use the full 
capability of the system by leveraging industrial-strength PowerVM virtualization for AIX, 
IBM i, and Linux. PowerVM offers the capability to dynamically adjust system resources 
based on workload demands so that each partition gets the resources it needs. Active 
Memory Expansion is a technology, introduced with POWER7, that enables the effective 
maximum memory capacity to be much larger than the true physical memory. The  
processor includes built-in accelerators that increase the efficiency of the compression and 
decompression process, allowing greater levels of expansion up to 125%. This can enable a 
partition to do significantly more work or enable a server to run more partitions with the same 
physical amount of memory.

The Power 750 and Power 760 servers are 5U 19-inch rack-based systems. The Power 750 
offers configurations of up to 32  cores and 1 TB of memory. The Power 760 offers 
configurations of up to 48  cores and 2 TB of memory. Both are able to contain 
internal I/O and also connections to additional drawers for external I/O. These systems 
contain a single processor planar board with up to four pluggable processor modules. The 
processor modules have eight installed cores (8404-E8D) or 12 installed cores (9109-RMD).

The  module, built with 32 nm technology, dramatically increases the number of 
circuits available, supporting a larger L3 cache (80 MB: 2.5 times greater than its POWER7 
predecessor), and new performance acceleration features for Active Memory Expansion and 
hardware-based data encryption. Power servers using this new module will be able to achieve 
higher frequencies within the same power envelope and improved performance per core 
when compared to POWER7 based offerings.

1

Summary of Contents for Power 750 Express













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands