IBM Power 750 Express 8408-E8D, Manual

Page: 41 / 66

9. Install an operating system and update the operating system:
v
For instructions to install the AIX operating system, see Installing AIX (http://
publib.boulder.ibm.com/infocenter/systems/scope/hw/topic/ipha8/iphayinstallaix.htm).
v
For instructions to install IBM i, seeInstalling IBM i (http://publib.boulder.ibm.com/infocenter/
systems/scope/hw/topic/ipha8/iphaxinstallos400.htm).
v
For instructions to install the Linux operating system, see Installing Linux on Power Systems
servers (http://publib.boulder.ibm.com/infocenter/lnxinfo/v3r0m0/topic/liaae/
lcon_Installing_Linux_on_System_p5.htm).
v For instructions to install the VIOS operating system, see Installing VIOS (http://
publib.boulder.ibm.com/infocenter/systems/scope/hw/topic/p7hch/iphchinstallvios.htm).
Completing the server without using a management console
You must perform these tasks to complete the server setup if you do not have a Hardware Management
Console (HMC).
1. Plug in the power cords. For instructions, see “Connecting the power cables to the system” on page
25.
2. Confirm that the system is in standby mode. The green power status indicator on the front control
panel is flashing slowly, and the
DC Out indicator lights on the power supplies are flashing. If none
of the indicator lights are flashing, check the power cord connections. For more information, see
“Common system attention LEDs and system reference codes” on page 40.
3. To check the firmware level on the managed system and to update the time of day, complete the
following steps:
a.
Access the Advanced System Management Interface (ASMI). For instructions, see Accessing the
ASMI without an management console (http://publib.boulder.ibm.com/infocenter/systems/
scope/hw/topic/p7hby/connect_asmi.htm).
b. On the ASMI Welcome pane, note the existing level of server firmware in the upper-right corner
under the copyright statement.
c. Update the time of day. In the navigation area, expand System Configuration .
d. Click Time of Day . The right pane displays a form that shows the current date (month, day, and
year) and time (hours, minutes, and seconds).
e. Change the date value, the time value, or both, and click Save settings .
4. Connect your disk drives and PCI adapters, if applicable. For more information, see Disk drives
(http://publib.boulder.ibm.com/infocenter/systems/scope/hw/topic/p7hal/
p7halkickoff_75x_76x.htm) and PCI adapters (http://publib.boulder.ibm.com/infocenter/systems/
scope/hw/topic/p7hak/p7hak_pciadapters_front.htm).
5. To start a system that is not managed by an HMC or ASMI, complete the following steps:
a.
Open the front door of the managed system.
b. Press the power button on the control panel. For instructions, see Power on (http://
publib.boulder.ibm.com/infocenter/systems/scope/hw/topic/p7hby/poweronoff.htm).
6. Install an operating system and update the operating system, if required.
For instructions to install the Virtual I/O Server (VIOS) operating system, see Installing VIOS
(http://publib.boulder.ibm.com/infocenter/systems/scope/hw/topic/p7hch/iphchinstallvios.htm).
7. Update the system firmware, if required.
v
For instructions to get firmware fixes through the AIX or Linux operating system, see Getting
server firmware fixes through AIX or Linux without a management console (http://
publib.boulder.ibm.com/infocenter/systems/scope/hw/topic/p7ha5/fix_firm_no_hmc_aix.htm).
v
If you are using VIOS, see Updating the Virtual I/O Server's firmware and device microcode with
an Internet connection (http://publib.boulder.ibm.com/infocenter/systems/scope/hw/topic/
p7ha5/fix_virtual_firm_ivm.htm).
Completing the server setup
29