background image

Environment

Temperature and Humidity

A 2104 has the following environmental limits:

Air Temperature

Relative Humidity

Maximum Wet Bulb

Operating

10°C to 40°C
(50°F to 104°F)

8% to 80%
noncondensing

27°C (80°F)

Recommended
operating point

22°C
(72°F)

45%

Recommended
operating range

20°C to 25°C
(68°F to 77°F)

40% to 50%

Nonoperating

10°C to 52°C
(50°F to 126°F)

8% to 80%
noncondensing

27°C (80°F)

Storing

1°C to 60°C
(34°F to 140°F)

5% to 80%
noncondensing

29°C (84°F)

Shipping

−40°C to 60°C
(−40°F to 140°F)

5% to 100%
condensing but
not precipitating

29°C (84°F)

Notes:

1. The recommended operating temperature is 22°C (72°F) or lower. At lower

temperatures, the risk of failure in the unit is reduced. If the operating temperature
is above 22°C (72°F) for long periods of time, the 2104 is exposed to a greater risk
of failure from external causes.

2. The nonoperating environment must not exceed the operating environment limits for

longer than 60 days.

3. The storage environment must not exceed the operating environment limits for

longer than 1 year.

4. Substantial deviations from the recommended operating range, in either direction, if

sustained for extended periods of time, will expose the 2104 to greater risk of failure
from external causes.

Altitude

Altitude (from sea level) limits for both models are:

Operating: 0 to 2133 m (0 to 7000 ft)
Nonoperating: −304.8 m to 12 192 m (−1000 to 40 000 ft)

Note: The upper dry bulb temperature limit of the rack-mounted unit is lowered by 1°C

(2°F) for every 137 meters (450 feet) above 915 meters (3000 feet). The upper
wet bulb temperature limit is lowered by 1°C (2°F) for every 274 meters (900
feet) above 305 meters (1000 feet).

14

2104 Models DU3 and TU3 Hardware Technical Information

Summary of Contents for DU3 2104





































Reviews: