IBM CS821 Service Manual Download Page 64 | Manualshive

Page: 64 / 118

background image

b.

After the system processor module is properly aligned, press the top of the pen to release it from
the processor. Lift the pen off the processor.

10.

Move the processor heat sink to the processor. If either the TIM or the heat sink is damaged, replace
both the TIM and the heat sink. Carefully lower the heat sink over the system processor module,
ensuring that the holes in the heat sink (A) align with the two guide pins (B) on the socket, as
shown in Figure 55.

Figure 54. Lowering the processor into the socket

Figure 55. Installing the heat sink

48

Power Systems: Servicing the IBM Power System S821LC (8001-12C) or the IBM CS821 (8005-12N)

«
...
62
63
64
65
66
...
»

Summary of Contents for CS821























































































































Reviews:

No comments

Related manuals for CS821

Brand: Magpowr Pages: 4

Brand: Earlex Pages: 4

Brand: JVA Pages: 22

Brand: Parkside Performance Pages: 134

Brand: H3C Pages: 5

Brand: Zhaoxin Pages: 5

Brand: Aprimatic Pages: 2

Brand: Malibu Boats Pages: 4

Brand: US SAWS Pages: 4

Brand: U-Line Pages: 12

Brand: Goobay Pages: 4

GALAXY EVO EGX850EWT

Brand: ENERMAX Pages: 60

Brand: Kikusui Pages: 64

Brand: Grizzly Pages: 56

Brand: Pro'sKit Pages: 12

Brand: Bostitch Pages: 32

2787-2344 0000-00 0 Series

Brand: WAGO Pages: 78

Brand: Far Tools Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands