background image

4

 

 3:  O

PTION 

A: E

MBEDDED 

N

ETWORK 

M

ODULE 

C

ONFIGURATION

 

I

NTERACTION WITH OTHER NETWORK MANAGEMENT APPLICATIONS

 

The figure below identifies and briefly describes the network management applications that can work with a UPS that connects 
to the network through the Embedded Network Module. 

 

Q

UICK 

C

ONFIGURATION

 

Overview 

You must configure the following TCP/IP settings before the Embedded Network Module can operate on a network: 

 

The IP address of the Embedded Network Module 

 

The subnet mask 

 

The default gateway 

TCP/IP configuration methods 

To define the TCP/IP settings needed by the Embedded Network Module, use the Embedded Network Module Wizard (see the 
following section).

 

Other methods available are:

 

 

A DHCP or BOOTP server (see User’s Manual on 

Embedded Network Module CD

)

 

 

A local computer (see User’s Manual on 

Embedded Network Module CD

 

A networked computer (see User’s Manual on 

Embedded Network Module CD

Embedded Network Module Wizard 

The Embedded Network Module Wizard can be used at a Windows 98, Windows NT 4.0, Windows 2000 or Windows XP com-
puter to configure the Embedded Network Module. If a different operating system is being used, refer to the 

Embedded Network 

Module CD

1.  Obtain an IP address, subnet mask and default gateway from your Network administrator before proceeding. 

2.  Follow the on-screen instructions to install the Wizard from the 

Embedded Network Module

 

CD

3.  Launch the Wizard, when prompted, or, if prompted to restart the computer, access the Wizard from the 

Start

 menu 

after the computer has restarted. 

4.  Wait for the Wizard to discover the unconfigured Embedded Network Module, then follow the on-screen instructions. 

Note: If you leave the 

Start a Web browser when finished

 option enabled, you can use 

apc

 for both the 

User Name

 

and 

Password

 to access the Embedded Network Module through your browser. 

H

OW TO 

M

ANAGE THE 

UPS 

VIA A 

C

ONFIGURED 

E

MBEDDED 

N

ETWORK 

M

ODULE 

 

Overview  

Once the Embedded Network Module is running on your network, you can use the ftp, Telnet, SNMP or Web interface to ac-
cess the Embedded Network Module. 
Note: For more information about how to use the web interface, and details on the ftp, Telnet and SNMP interfaces, see the

 

User's Guide

 

on the 

Embedded Network Module CD

 (.

/doc/usrguide.pdf

). 

Summary of Contents for 3000XLV






Reviews: