Mapa de Controlo de Parâmetros DMX
Canal No
DMX512 fig.
Conteúdo
0~49 Controlo
por
som
50~99 Raio
Auto
100-149 Animação
Auto
Canal 1
Modo
150~255 Manual
0 Laser
off
Canal 2
Selecção
Cor
1-255
Verde, vermelho, azul,
amarelo, ciano, branco
Canal 3
Selecção de
padrão
0-255 Padrões
0-127 Manual
128-191
De baixo para cima
speedy
Canal 4
Movimento
vertical
192-255
De cima para baixo
speedy
1~127 Manual
128-191
Direita para a esquerda
Canal 5
Movimento
Horizontal
192-255
Esquerda para a direita
Canal 6
Rotação
Vertical
0-255
Lento para rápido
Canal 7
Rotação
Horizontal
0-255
Lento para rápido
0-127 Manual
128-191 Rotação
direita
Canal 8
Rotação
192-255 Rotação
esquerda
0 Estático
1-85 Pequeno
para
grande
86-170
From big to small
Canal 9
Zoom
171-255 Auto
zoom
0 Tamanho
normal
Canal 10
Tamanho de
padrão
1-255 Pequeno
para
grande
Canal 11
Ponto e linha
0-255
Linha e ponto
Canal 12
Velocidade
de pisca
0-22
Lento para rapido
Function setting
Use the dipswitches to assign the unit’s function: DMX/slave, sound
active or AUTO mode.
For DMX mode, set the DMX address. Each
dipswitch represents a binary value.
See the “Function chart”.
0=OFF 1=ON X=OFF or ON
DIPSWITCH CHART
#1 #2 #3
#4
#5
#6
#7
#8
#9
#10
FUNCTION
0
X
X
X
X
X
X
X
X
0 SOUND
ACTIVE
1
X
X
X
X
X
X
X
X
0 AUTO
-beam
1 1
X
X
X
X
X
X
X
0 AUTO-animation
X
X
1
X
X
X
X
X
X
0 Slave
for
Sound
and Auto
1
SET DMX ADDRESS FOR DMX
MODE
1 DMX
Sound Active
The change of the laser pattern is controlled by sound. That means the
rhythm of the sound controls the change of the laser pattern. Turn the
sensitivity knob in the clockwise direction to increase the fixture’s
sensitivity to sound, turn the knob in the counterclockwise direction to
decrease.
AUTO
Auto cycles the built-in programs without being controlled externally.
DMX Control
The system only accepts the DMX512 signal of international standard to
control the system mode, the laser pattern ON /OFF, the size, the position,
the speed, etc.
Master-Slave Operation
This mode will allow you to link up to 32 units together without controller.
1. Install the units in a suitable position (laying or appending).
2. Choose a unit to function as Master mode, set dipswitch to select
Sound Active or AUTO mode. The others must be set to Slave mode, set
dipswitch to select Slave mode.
Slave units set #3 on
3. Use standard XLR microphone cable chain your units together via the
XLR connector on the rear of the units. For longer cable runs we suggest
a terminator at the last fixture.
4. Turn on the all units' power, the units begin to reset, then the units
begin working. The slave units will react the same as the master unit.
5. The units will react to the low frequencies of music via the internal
microphone. Adjust the audio sensitivity knob on the back of the master
unit to make the unit more or less sensitive in sound active. The panel
has LED indicating for sound active.
