Settings on the Carrier Board
RP-103-SMC User Manual
15
2.4. Connectors on RP-103-SMC
P1
DC-in
CN1 QSPI
P2
Internal DC-in
CN2 SPI
(2.2.1
)
P3
SD/MMC slot
CN3 SPI
(2.2.1
)
P4
SD/MMC slot
(2.2.1
)
CN4 MIPI DSI0
P5
HDMI TX1/EDP TX
CN5 LVDS2 ch0
P6
HDMI TX2
(2.2.1
)
CN6 LVDS2 ch1
P7
HDMI RX
(2.2.1
)
CN7 DSI0/LVDS2 Backlight
P8
LAN0
CN8 DSI0/LVDS2 TP (i2c for touch)
P9
LAN1
(2.2.1
)
CN9 MIPI DSI1
(2.2.1
)
P10 mPCIe slot
CN10 DSI1 Backlight
(2.2.1
)
P11 SIM slot
CN11 LVDS0 ch0
P12 M.2 E-Key 2230 slot
CN12 LVDS0 ch1
P13 USB1/2
CN13 LVDS0 Backlight
P14 MXM3 slot
CN14 LVDS1 ch0
(2.2.1
)
P15 DSI0/LVDS2 Backlight power select CN15 LVDS1 ch1
(2.2.1
)
P16 DSI0/LVDS2 LCD power select
CN16 LVDS1 Backlight
(2.2.1
)
P17 DSI1 Backlight power select
(2.2.1
)
CN17 LVDS1 TP (i2c for touch)
(2.2.1
)
P18 DSI1 LCD power select
(2.2.1
)
CN18 Speaker L
P19 LVDS0 Backlight power select
CN19 Speaker R
P20 LVDS0 LCD power select
CN20 USB3/4
P21 LVDS1 Backlight power select
(2.2.1
)
CN21 MIPI CSI1
(2.2.1
)
P22 LVDS1 LCD power select
(2.2.1
)
CN22 MIPI CSI2
P23 Headphone & Mic.
CN23 SATA0
(2.2.1
)
P24 Line In/Out
CN24 SATA power
(2.2.1
)
P25 OTG USB
CN25 SATA1
P26 RS232/422/485
CN26 SATA power
SW1 Boot Mode Select
CN27 CAN0/1
(2.2.1
)
SW2 UART Mode Select
CN28 CAN2/3
SW3 I/O & Display Select
CN29 COM1/3
SW4 Power ON/OFF
button
CN30 UART0/4
(2.2.1
)
SW5 Sleep button
CN31 DIO
SW6 LID button
CN32 FAN
SW7 Reset button
CN33 UART(4-wire)
CN34 BTB Conn
(2.2.1
)
CN35 RTC BAT
Note:
(2.2.1): RM-N8 module use only
Summary of Contents for RP-103-SMC
