![background image](http://html1.mh-extra.com/html/ibanez/troubadour/troubadour_owners-manual_604557009.webp)
7
EN
G
LI
SH
Names and Function on Each Part
Front Panel
1. POWER LED: This LED will light when amp power is activated by
the power switch.
2. INPUT LEVEL: Switches the signal level from MIC INPUT, line
level or mic level.
3. PHANTOM ON/OFF: Switches the phantom power ON/OFF. The
phantom power can 15V to your condenser microphone
that connects with MIC INPUT. When you use this switch, turn
down the VOLUME to 0.
4. MIC INPUT: Balanced input terminal with XLR Jack. 1-GND,
2-HOT, 3-COLD.
5. INST. INPUT: 1/4” phone jack input.*
1
6. CLIP INDICATOR: When this LED is illuminated in red, the pre-
amp is clipping. To reduce clipping turn down the VOLUME.*
1
7. VOLUME: Controls the pre-amplifier level.*
1
8. 3 BAND EQ: Refer to the spec sheet at the end of this manual for
frequencies and levels.
9. CHORUS: Controls the speed of the chorus effect. Turn this con-
trol to the right to increase the speed. This function will be off at “0”
position.*
1
10. REVERB: Controls the reverb level. This function will be off at “0”
position.*
1
11. NOTCH FILTER: This is a notch filter that reduces feedback. Turn
this control until feedback stops. This function will be off at “0” posi
-
tion.*
2
12. MASTER: Controls the output level from this amplifier. Doesn’t
work for LINE OUT and AUX IN signal.
13. PHASE INVERT: Inverts the phase of signal. This helps you stop
feedback.*
2
14. MUTE: Mutes the signal from MIC INPUT and INST. INPUT., and
the LED lights. Doesn’t work for LINEOUT and AUX IN signal.
15. PHONES: 3.5mm stereo mini output jack for stereo headphones.
The sound is not reproduced through the built-in speaker when
headphones are in use. Meanwhile, LINEOUT signal still outputs.
Warning:
This phones output produces a large volume of sound. Ensure that
the MASTER and AUX VOLUME has been turned down before
beginning to play using the headphones, and then slowly increase
the volume until it has reached the desired level. Note that the
noise and distorted sound signals produced when inserting or re-
moving the headphone plug at high volume levels will result in
damage to the headphones and to the user’s hearing.
16. AUX IN: 3.5mm stereo mini jack. This jack is designed to be con-
nected to the headphone output of a portable CD or MP3 player, or
similar device. Use the volume control of your portable player along
with the volume control on the amp to adjust the desired volume.
17. AUX VOLUME: Controls the signal level of AUX IN.
18. LINEOUT: Monaural 1/4” phone jack with a line level output. You
can connect to an external mixing console or similar equipment.
REVERB and CHORUS signal are output in stereo.
19. FOOTSWITCH INPUT: Connect the provided footswitch.
20. FOOTSWITCH FUNCTION SWITCH: Switches the footswitch
function that has 2 modes, EFFECT CONTROL MODE and
NOTCH FILTER MODE. Refer to “Using Footswitch”.
21. TILT UP BAR: The built-in tilt system allows for better monitoring.
*
1
: The function works in each channel independently.
*
2
: The function might not work perfectly under bad conditions of use.
Rear Panel
A. AC INLET: Connect the included AC power cable to this connector.
Only use this amp with the voltage indicated on the panel.
B. POWER SWITCH: This switch turns the power on/off. When you
are not using the amp, please leave it turned off.