![background image](http://html.mh-extra.com/html/ibanez/mimx150h/mimx150h_owners-manual_604546013.webp)
13
ENGLISH
3. Saving a sound you created
In this section you'll learn how to save a sound you've created. We'll
save your new sound in bank A, channel 1.
* For details on initializing the memory, refer to 5. Factory reset
1) Make sure that the
5
Display indicates M. Then, hold down the switch
marked "1" for three seconds or longer. When the settings have been
saved, the
5
Display will indicate A1, and will blink.
A sound you create in manual mode as described here can be saved in
any channel. A sound you create in each bank can be saved in a chan-
nel within that bank.
Here's an example.
2) Up to this point, we've used bank A, channel 1 to create a sound, but
now we're going to slightly adjust the position of each control and save
the result in bank A, channel 2. Perform the following steps.
By saving your edited sound in another channel, you'll be able to com-
pare the two sounds. Next we're going to try using rhythm patterns.
Note: Each channel consists of two banks, A and B. If you
want to save settings in bank A, channel 1 as described in this
tutorial after creating your sound in manual mode, you must
first click "1", make sure that you're currently in bank A, and
then click the MANUAL switch once again to return to manual
mode before you proceed with the following steps.
Hold down for three seconds or longer.
Hold down for three seconds
or longer
Edit the sound of
bank A, channel 1
The sound is saved
in bank A, channel 2
4. Using rhythm patterns
This section explains how to use rhythm patterns.
1) We'll start by playing a rhythm. Click the ON/OFF switch. The TAP
switch will blink, and you'll hear drum sounds.
Note: Use the RHYTHM knob to adjust the volume appropriately.
2) Next we'll change the pattern. Press + or - until the
5
Display indi-
cates 16.
3) Let's make the tempo a bit faster. Click the TAP switch several times
at a consistent rhythm until the
5
Display indicates 120.
You can use rhythm patterns by following the procedure described above.
5. Factory reset
This section explains how to initialize the amp to the factory-set condi-
tion.
1) While holding down the MANUAL switch as shown in the illustration
below, turn on the
11
POWER switch. The
5
Display will indicate AL.
2) If you press the MANUAL switch in this state, all data will return to the
factory-set condition.
3) If you decide to cancel without resetting, operate any control other
than the MANUAL switch. You will exit factory reset mode.
Play a rhythm pattern Change the rhythm pattern Change the rhythm speed
While holding down the
MANUAL switch, turn on
the POWER switch.
The display will
indicate AL.
Click the MANUAL
switch.
Summary of Contents for MIMX150H
