background image

FCC STATEMENT 

 

This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 

pro-vide reasonable protection against harmful interference in a residential 

installation. This equipment generates uses and can radiate radio frequency energy 

and, if not in-stalled and used in accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by 

turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to 

which the receiver is connected.   

 

Consult the dealer or an experienced radio / TV technician for help. 

This device complies with part 15 of the FCC Rules. Operation is subject to the 

following two conditions: 

1) 

This device may not cause harmful interference. 

2) 

This device must accept any interference received, including interference 

that may cause undesired operation. 

Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment. 

CE Mark Warning 

 

This is a class B product. In a domestic environment, this product may cause radio 

interference, in which case the user may be required to take adequate measures.

 

Summary of Contents for Baton iB-OR246150N




















Reviews: